This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Kernel panic when booting (Qotom Mini PC Q500P)

Hello all,

I received my hardware, which I discussed here, for my XG yesterday.

First I had the problem that the installation did not go through, but after I set everything to legacy in the BIOS, the installation was without problems.

However, I now get a kernel panic when booting:

Unfortunately, booting with acpi=off does not help either. Here is a photo of booting with acpi=off

Does anyone have an idea how I can solve the problem?

Regards

Marc



This thread was automatically locked due to age.
Parents
  • On Q9XXGE-P which I test for friend I get pretty same errors(Different interfaces) but it normally boot and load XG 18.5 ...

    Sophos XG v18.5.x - Supermicro CSE-512, X10SLM+F, E3-1220v3 8GB RAM, Intel X520-DA2

  • Is there a public download for 18.5? I have only found an update

  • There is no iso for 18.5. You need download 18.0 ISO, install it and then install 18.5.1 update(SW-18.5.1_MR-1.SFW-326.sig).

    Sophos XG v18.5.x - Supermicro CSE-512, X10SLM+F, E3-1220v3 8GB RAM, Intel X520-DA2

  • Unfortunately this way is not possible, because the 18.0 does not start :-(

  • What HDD do you use? SATA? Im not sure if M.2 or NVME are supported.
    Did you update bios? My had one from 2020 and is normaly install 18.0 and update to 18.5  Im update it to last one from 2021 and  18.5 run. I need to disable UEFI and use legacy options, and Im disable speedstep and other saving options.

    Only issue I had right now is boot messages but it then boot and run. And last 3 days I have issue that WAN connection do not work anymore. It get IP, GW, DNS from DHCP but gw stay red and do not change to green. Also ping and traceroute do not work on wan interface... Im try change WAN interface from Port8 to Port7 and to Port4 but none help...

    P.S: This underlined issue is resolved. XG has been tested in internal LAN and WAN IP on that XG has receive same network as configured on XG VLAN... Im found this when im check routes on advanced console and see two routes for same network(one on WAN and onother on VLAN.

    Sophos XG v18.5.x - Supermicro CSE-512, X10SLM+F, E3-1220v3 8GB RAM, Intel X520-DA2

  • Did you update bios? My had one from 2020 and is normaly install 18.0 and update to 18.5  Im update it to last one from 2021 and  18.5 run. I need to disable UEFI and use legacy options, and Im disable speedstep and other saving options.

    From where did you get the current bios? I only found the existing bios at Qotom.

  • Im get it from official download site:

    https://www.qotom.shop/download/BIOS/

    Be carefull if model have more than one revision to check(On Frinds is under RAM slot) which revision do you have...

    Sophos XG v18.5.x - Supermicro CSE-512, X10SLM+F, E3-1220v3 8GB RAM, Intel X520-DA2

  • I have my 18.5 installation running on a system on 128GB M.2 PCIe NVMe SSD
    No problems at all.

     
    SFVH (SFOS 19.5.1 MR-1-Build278)  - Last (re)boot on Februari 20 2023
    Asus H410i-plus - Pentium 6605 Gold - 250GB M.2 PCIe NVMe SSD - 8GB - 3 ports
    [If any of my posts are helpful to you please use the 'Verify Answer' link]
Reply
  • I have my 18.5 installation running on a system on 128GB M.2 PCIe NVMe SSD
    No problems at all.

     
    SFVH (SFOS 19.5.1 MR-1-Build278)  - Last (re)boot on Februari 20 2023
    Asus H410i-plus - Pentium 6605 Gold - 250GB M.2 PCIe NVMe SSD - 8GB - 3 ports
    [If any of my posts are helpful to you please use the 'Verify Answer' link]
Children