Guest User!

You are not Sophos Staff.

Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 15 replies
  • Subscribers 29 subscribers
  • Views 1781 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Kernel panic when booting (Qotom Mini PC Q500P)

initB10r

Hello all,

I received my hardware, which I discussed here, for my XG yesterday.

First I had the problem that the installation did not go through, but after I set everything to legacy in the BIOS, the installation was without problems.

However, I now get a kernel panic when booting:

Unfortunately, booting with acpi=off does not help either. Here is a photo of booting with acpi=off

Does anyone have an idea how I can solve the problem?

Regards

Marc



This thread was automatically locked due to age.
Parents
  • 0

    On Q9XXGE-P which I test for friend I get pretty same errors(Different interfaces) but it normally boot and load XG 18.5 ...

  • 0 in reply to Dejan Bukovec

    Is there a public download for 18.5? I have only found an update

  • 0 in reply to initB10r

    There is no iso for 18.5. You need download 18.0 ISO, install it and then install 18.5.1 update(SW-18.5.1_MR-1.SFW-326.sig).

  • 0 in reply to Dejan Bukovec

    Unfortunately this way is not possible, because the 18.0 does not start :-(

  • 0 in reply to initB10r

    What HDD do you use? SATA? Im not sure if M.2 or NVME are supported.
    Did you update bios? My had one from 2020 and is normaly install 18.0 and update to 18.5  Im update it to last one from 2021 and  18.5 run. I need to disable UEFI and use legacy options, and Im disable speedstep and other saving options.

    Only issue I had right now is boot messages but it then boot and run. And last 3 days I have issue that WAN connection do not work anymore. It get IP, GW, DNS from DHCP but gw stay red and do not change to green. Also ping and traceroute do not work on wan interface... Im try change WAN interface from Port8 to Port7 and to Port4 but none help...

    P.S: This underlined issue is resolved. XG has been tested in internal LAN and WAN IP on that XG has receive same network as configured on XG VLAN... Im found this when im check routes on advanced console and see two routes for same network(one on WAN and onother on VLAN.

Reply
  • 0 in reply to initB10r

    What HDD do you use? SATA? Im not sure if M.2 or NVME are supported.
    Did you update bios? My had one from 2020 and is normaly install 18.0 and update to 18.5  Im update it to last one from 2021 and  18.5 run. I need to disable UEFI and use legacy options, and Im disable speedstep and other saving options.

    Only issue I had right now is boot messages but it then boot and run. And last 3 days I have issue that WAN connection do not work anymore. It get IP, GW, DNS from DHCP but gw stay red and do not change to green. Also ping and traceroute do not work on wan interface... Im try change WAN interface from Port8 to Port7 and to Port4 but none help...

    P.S: This underlined issue is resolved. XG has been tested in internal LAN and WAN IP on that XG has receive same network as configured on XG VLAN... Im found this when im check routes on advanced console and see two routes for same network(one on WAN and onother on VLAN.

Children