Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 58 replies
  • Subscribers 2 subscribers
  • Views 13747 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

[7.403] WAN NIC Down after up2date to 7.403!

BarryG
After installing the 7.403 up2date, my internet connection wouldn't come up.

It is completely possible that my ISP decided to wig out at the same time; I'm not sure.

My LAN was working, and it's the same model NIC as the WAN.

ethtool was showing the WAN NIC up and down, and ifconfig was showing it up and down and up with and without an IP.

the kernel log was repeating
2009:06:08-16:55:05 fw kernel: e1000e: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None

I messed with it for awhile and rebooted once and powered off once, but couldn't get it back up.
I'm now back on 7.402 after a re-install/restore, and it's working fine.

Question: did the network driver or anything else change in 7.403 that could cause something like this?

Thanks,
Barry


This thread was automatically locked due to age.
Parents
  • 0
    I tried the up2date again; lost network again... tried lowering the network link to 100 or 10mbps but it never worked... I could ping the gateway for short periods with about 90% loss, still kept seeing messages in the kernel log like
    2009:06:08-18:14:27 fw kernel: e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None

    Thanks,
    Barry
  • 0 in reply to BarryG
    I take it you are seeing the issue on the last machine listed in your signature... I've installed the 7.403 up2date on several different units that use the e1000 driver, but haven't seen that problem yet... do you see link issues on the ports if you connect them to a different switch?

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • 0 in reply to BAlfson
    I've emailed support about this problem again. Same support ID as posted above.

    Barry
  • 0 in reply to BarryG
    I've emailed support about this problem again. Same support ID as posted above.

    Barry


    I'm curious, are we using the same Intel gigabit cards?
    While our boards are different (Intel v. MSI), I'm using the Intel Pro1000 MT Dual Port (64bit PCI-X) cards (in a 32bit slot of course).  
    Granted, I know all of the Intel cards use the e1000 universal drivers, but I'm just curious.  Have you tried switching around the interfaces?  
    E.g. assign Port A on the card to External and Port B to Internal?  (Port A on my card always appears as Eth1 and gets assigned Internal and Port B as Eth2 and I always assign it External (the on-board NIC shows up as Eth0).  

    Intel PRO/1000 MT Dual Port Server Adapter - Overview

  • 0 in reply to Jhaislet
    Hi, both my NICs are onboard... lspci says "Intel Corporation 82574L"...

    Since my last post, my dhcp lease from my ISP expired, so I'm now forced to keep manually resetting the NIC, or downgrade to 7.402 AGAIN or 'upgrade' to the beta.
    [:(]

    Barry
  • 0 in reply to BarryG
    7.460 seems to be better here.

    Barry
  • 0 in reply to BarryG
    I had run into this issue a few days ago. But all I had to do was unplug and re-plug the ethernet wire and things started working again.
    Hoping things stay connected until 7.404 comes out or I have a chance to install 7.460.
  • 0 in reply to JimmyM
    Looks like 7.404 addresses this issue...

    https://community.sophos.com/products/unified-threat-management/astaroorg/f/52/t/26998

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • 0 in reply to BrucekConvergent
    Looks like 7.404 addresses this issue...

    http://www.astaro.org/astaro-gateway-products/hardware-installation-up2date-licensing/26588-axg-7-404-soft-release.html


    Very nice!  Astaro is really on the ball!
    Quick question, I'm currently at 7.402 and 7.403 causes reboot issues for my remote machine.  Can I skip 7.403 and install 7.404 on top of 7.402?  Or do I need to go ahead & do 403 and then put on 404?
  • 0 in reply to Jhaislet
    You'll have to install 7.403 and 7.404 in sequence (you can't skip an up2date, they are not cumulative)... however, just make sure that 7.403 and 7.404 are uploaded to the up2date manager, then click the update to latest version button; both updates will apply and the unit will reboot and be at version 7.404.

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • 0 in reply to BrucekConvergent
    Incidentally, if this is a remote, production unit, that is far, far away and that you have a hard time getting to in the event of an issue, I would wait a while until others have tested this up2date; errors have been found in other "Soft Releases" before... if it's within reach, or it's no problem to go to the unit and reload from ISO and restore backup, then it's no big deal if it fails.

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • 0 in reply to BrucekConvergent
    You'll have to install 7.403 and 7.404 in sequence (you can't skip an up2date, they are not cumulative)... however, just make sure that 7.403 and 7.404 are uploaded to the up2date manager, then click the update to latest version button; both updates will apply and the unit will reboot and be at version 7.404.


    Very good, thanks for the confirmation.  I was 99% sure the up2date packages weren't cumulative, but wanted to make sure.
Reply
  • 0 in reply to BrucekConvergent
    You'll have to install 7.403 and 7.404 in sequence (you can't skip an up2date, they are not cumulative)... however, just make sure that 7.403 and 7.404 are uploaded to the up2date manager, then click the update to latest version button; both updates will apply and the unit will reboot and be at version 7.404.


    Very good, thanks for the confirmation.  I was 99% sure the up2date packages weren't cumulative, but wanted to make sure.
Children
No Data
Cookie Information Banner