[6.819] Hardware-Problems, VIA VT6102(Rhine)

Today i've tested a new Via Epia CN10000 with fanless C7 processor. Everythink worked fine, even a SATA-disk was no problem.

But the onboard-ethernet-adapter didn't work correct. A fresh installation with this interface as the internal interface didn't not work (interface is not reachable), using it as a second interface worked, but was unstable. ICMP-pings needed about 500-2000ms, so this network-adapter ist not usable.

I tried different cables, different switches, connected my test-workstation directly via cross-connect and tried it with switched-off autonegotiation - but it didn't help. So i installed WinXP - and everything worked fine!

I think ASG has a driver-problem with VT6102-lan-chipset (or VT8235 chipset). I hope Astaro will fix/update those linux-drivers.

Parents

0 HolgerE over 18 years ago

Please provide output of 'lspci --vvxn', 'lspci -vvx' and 'hwinfo --netcards'. Thanks!
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Suppentrulli over 18 years ago in reply to HolgerE

Hi Holger,

output is attached. I use an Epia CN10000 + Compaq NC3134 dual-ethernet adpater.

Thanks in advance

lspci-vvxn.txt
lspci-vvx.txt
hwinfo-netcards.txt
- lspci-vvxn.txt
- View
- Hide
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 HolgerE over 18 years ago in reply to Suppentrulli

Please provide the boot messages (output of 'dmesg') and /proc/interrupts. Also, check the usual suspects, namely ACPI (acpi=off boot) and APIC (lapic=off boot). What does tcpdump show?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Suppentrulli over 18 years ago in reply to HolgerE

Hi Holger,

first of all: i've updated to 6.836. For a better understanding, here is my config-overview:

eth0 [Via Rhine, build-in]: 192.168.0.1
eth1 [Compaq NC3134 dual-port]: 172.16.0.1
eth2 [Compaq NC3134 dual-port]: DSL-pppoe

After normal booting, eth1 & eth2 (NC3134) work fine, eth0 (Rhine) is real slow, ping-replies take between 500 and 2000ms, the interface is not usable. Tcpdump shows nothing that seems to be wrong (in my opinion):

dmesg.txt
interrupts.txt
tcpdump_eth0.txt

After booting with "acpi=off" and "lapic=off", it's the other way round [:S] eth0 (Rhine) is working fine and eth1 (NC3134) is absolutely slow...

dmesg_acpi_lapic_off.txt
interrupts_acpi_lapic_off.txt

What am i doing wrong? Should i try it with another network-adapter instead of using NC3134?
- dmesg.txt
- View
- Hide
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 JimmyM over 18 years ago in reply to Suppentrulli

Were the VIA C7 and VT6102 combination supported in v5/v6? If so, what modules were loaded?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 BanksDad over 18 years ago in reply to JimmyM

what is that interface tied to? i would not reccomend shutting off auto-negotiation. I tried that on my NIC -> cable modem and the performance was terrible! when I say terrible, I mean it was actually worse than a dial up modem. try turning auto-negotiate back on and tell us what it is hooked to. switch? modem? other?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Suppentrulli over 18 years ago in reply to BanksDad

Hi,
it doesn't matter how the interface is connected. I tried different switches, different cables, cross-connect-cable, different settings (autonegotiation on/off) - but that did not help. As i said above, the same system with WinXP works, i guess it has something to do with apci/interrupts or something like that.

@JimmyM:
i will test V5/V6 this weekend. Which command do i have to use to check which module is loaded?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Reply

0 Suppentrulli over 18 years ago in reply to BanksDad

Hi,
it doesn't matter how the interface is connected. I tried different switches, different cables, cross-connect-cable, different settings (autonegotiation on/off) - but that did not help. As i said above, the same system with WinXP works, i guess it has something to do with apci/interrupts or something like that.

@JimmyM:
i will test V5/V6 this weekend. Which command do i have to use to check which module is loaded?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Children

0 Suppentrulli over 18 years ago in reply to Suppentrulli

Hi there,

i've just tested V6.3 with my Epia CN10000 => the same problems!

Yesterday i've tried a Intel Pro 1000 MT dualport adapter, but I had the same problems as with my old NC3134.

I still think that ASG is doing something wrong with the IRQs, because with Windows XP running every adapter is working really fine (i did some load tests).

Forgot to say that i've tested with 6.915...
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Suppentrulli over 18 years ago in reply to Suppentrulli

Hej, this issue is fixed with 6.933 ! [H]
Now all my interfaces do work!

Thanks Astaro!
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel