Error during install of 2.0 beta

Hi, I want to install 2.0 Beta on my system using a SCSI-harddisk and CD-rom connected to a Adaptec 2940 controller. The CD-boots fine, but during the install it halts and displays the following error after the keyboard layout nenu:

Attempt to access beyond end of device

0b:01 rw=0 want 144564 limit 144562

Any suggestions what's happening here ?

Franc.

Parents

0 eldorado over 23 years ago

hello franc

try the following:

in the BIOS of the AHA2940 controller,
&A when aha2940 bios shows a message on the screen during boot, I think it's under advanced, but i'm not shure, change the value for "Support for DOS drives > 1GB"
from no to yes or from yes to no, it depends what value is now.

hope this helps

greeting
eldorado
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Franc over 23 years ago in reply to eldorado

Hi Eldorado,

I thought about that too and did that (it was set to 'yes' so I changed it to 'no'), but it didn't work. The error still occurs.

Franc.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 iDiC over 23 years ago in reply to Franc

Was there ever a solution to this one? I am getting the same thing. However I can go to IDE instead of SCSI but would rather have that option open to me.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Franc over 23 years ago in reply to iDiC

Hi, no I never got a solution for this one. So, I'm not using astaro.

Franc.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 iDiC over 23 years ago in reply to Franc

Drastic (maybe).

Well just an update on my issue then. I removed the SCSI controler from the box and I am still getting the same error.

Attempt to access beyond end of device

16:00 0b:01 rw=0 want 144564 limit 144562

iDiC
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 Franc over 23 years ago in reply to iDiC

Hi,

perhaps it's a little bit drastic yes, but the SCSI drive I have is the only one I can use. I don't have a spare IDE drive with the minimum requeirements, so I'm stuck without if it's not working with my SCSI-drive.

Franc.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 micio over 23 years ago in reply to Franc

hi everybody,
I'm not shure, but, try and see the tranfer rate of your cd-rom,maybe this is problem.
01:0b should be the sector of the rom-disk
rw=0 read and write=0 it can't read the rom-disk
and the rest should be request tranfer-rate.
You can update the firmware of the cd-rom and
re-burn the disk not with high speed( try at
1X).
ciao
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 iDiC over 23 years ago in reply to micio

Will look in to this this weekend.

Would be nice to have some input to the develpers if they have some time ....
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 iDiC over 23 years ago in reply to iDiC

Well ... nevermind. Looks like I'll just move on to beta3. Fingers crossed.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 iDiC over 23 years ago in reply to iDiC

More problems. Hardware related? Continued here.

[ 06 August 2001: Message edited by: iDiC ]
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Reply

0 iDiC over 23 years ago in reply to iDiC

More problems. Hardware related? Continued here.

[ 06 August 2001: Message edited by: iDiC ]
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Children

No Data