This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

slow http & socks proxy

hi
I have been using my astaro box as a router for quite some time now. however, I now want to make use of the socks5 proxy for surfing, downloading, etc.
Just surfing doesn't seem to be a problem but when I start a bigger download (eg a kernel from kernel.org) my download rate goes down to a 100 Byte/sec. Since I'm connected via german T-DSL (768 kbit downstream) I think this should be a little bit faster [:)]sec.
It's exacly the same with the http-proxy.
I know that proxies need more hardware resources but my astaro-box isn't that slow: EPIA VIA C3-533MHz, 128 MB, 10 GB UDMA drive (in UDMA mode), VIA Rhine II connected to internal network, Adaptec ANA62022 (port 1 connected to external net, port 2 is unused at the moment (will become dmz interface)). My Astaro Version is 4.0.12. DNS-Proxy is enabled.

while downloading, my system utilization looks like this:

CPU Utilization: Maximum: 37% Average: 7% Current: 9%
RAM Utilization: Maximum: 83991 kB Average: 79354 kB Current: 78390 kB
SWAP Utilization: Maximum: 4048 kB Average: 1498 kB Current: 4048 kB
Harddisk Usage: 
Filesystem           1k-blocks      Used Available Use% Mounted on
/dev/hda7               554332    234140    292036  44% /
/dev/hda1               317335     17773    283178   6% /emergency
/dev/hda3              2966888     35596   2780584   1% /var/log
/dev/hda5              1279612     48272   1165288   4% /var/chroot-mail
/dev/hda6               218150      4252    202635   2% /var/recovery
/dev/hda8              1279612     59864   1153696   5% /var/chroot-squid
/dev/hda9              2926572     33216   2744696   1% /var/chroot-report
none                     59672         0     59672   0% /var/shm

What am I doing wrong?   


This thread was automatically locked due to age.
Parents
  • mrseq,

    please check your interface settings and make sure that you have one default gateway only.
    (assigned by remote at the DSL interface)

    read u
    o|iver   
  • Hello together!
    Same problem here...

    My System is based on a Via Epia M10000 (Nehemiah).
    Onboard NIC: VIA VT6103 10/100 Base-T Ethernet PHY => VIA Rhine II
    Second NIC: D-Link  4 Port DFE-570TX

    What about IRQ sharing?

    Onboard Nic (eth0) is sharing IRQ 15  with eth4 from second NIC and onboard VGA-Card.
    Throughput on D-Link Ports are very well!
    Once and only Gateway is Outside PPOE (ETH4)

    Any interest from Astaro to get a EPIA Test-System to examine these Boards for listing in HCL?

    I live near Karlsruhe, so it would be no circumstance...  [;)]     
  • I only had one gateway so that wasn't the issue... I finally shut down my EPIA Astaro-Box. It was too damn slow and I couldn't figure out why (reinstalled the box several times..). I am now using a Celeron 300 / BX-Board, 256 MB, 20 GB and 3COM Nics (3c905b). The proxies are working at nearly full dsl-capacity (around 90-92 KB/sec). 
    So I'd say it's a kernel / driver issue...    
Reply
  • I only had one gateway so that wasn't the issue... I finally shut down my EPIA Astaro-Box. It was too damn slow and I couldn't figure out why (reinstalled the box several times..). I am now using a Celeron 300 / BX-Board, 256 MB, 20 GB and 3COM Nics (3c905b). The proxies are working at nearly full dsl-capacity (around 90-92 KB/sec). 
    So I'd say it's a kernel / driver issue...    
Children
No Data