Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 5 replies
  • Subscribers 2 subscribers
  • Views 1500 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

HA Cluster in different rooms

krowczynski
Hi everybody,

wanted to ask around if someone has an Clusterinstallation of the ASG in different rooms.
One node is located in room1 and the Otter node is located in room 2 while an active/passive Cluster is configured.

Thanks for some feedback.


This thread was automatically locked due to age.
Parents
  • 0
    There's no reason you can't do that... a network cable is a network cable, whether it's 2' long or 300' long.

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • 0 in reply to BrucekConvergent
    Hi,

    but how have I to configure it, if there is a switch and different VLANs between them.

    As I remember the ASG uses an 192.168.95... or so for the Clusterconfiguration....


    There's no reason you can't do that... a network cable is a network cable, whether it's 2' long or 300' long.
Reply
  • 0 in reply to BrucekConvergent
    Hi,

    but how have I to configure it, if there is a switch and different VLANs between them.

    As I remember the ASG uses an 192.168.95... or so for the Clusterconfiguration....


    There's no reason you can't do that... a network cable is a network cable, whether it's 2' long or 300' long.
Children
  • 0 in reply to krowczynski
    That is a networking question; just trunk the VLANs needed between the two rooms.  It's going to be a switch configuration issue, not a Sophos UTM issue.  If this is in a commercial installation, you may want to get a consultant to help you if you're unfamiliar with how to get those VLANs "present" in each room.

    As long as the HA port is on the same VLAN with the other HA ports (and they should be on their own VLAN / network segment), everything will work fine.

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • 0 in reply to BrucekConvergent
    Hi,

    thank you for your answer.
    I will create an seperate VLan for the HA and will configure it on the switches and than will see.

    Thanks once again

    That is a networking question; just trunk the VLANs needed between the two rooms.  It's going to be a switch configuration issue, not a Sophos UTM issue.  If this is in a commercial installation, you may want to get a consultant to help you if you're unfamiliar with how to get those VLANs "present" in each room.

    As long as the HA port is on the same VLAN with the other HA ports (and they should be on their own VLAN / network segment), everything will work fine.
  • 0 in reply to krowczynski
    Hi,

    thank you for your answer.
    I will create an seperate VLan for the HA and will configure it on the switches and than will see.

    Thanks once again


    Be sure to configure Jumbo Frames Support for the eth3 / HA interface.
    Otherwise, they won't see each other.


    Cheers,
    ciscoman
Cookie Information Banner