Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 9 replies
  • Subscribers 2 subscribers
  • Views 1572 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Installation Woes

ShadowLab
Ok, so.... I'm not sure what's happening here. I have Clarkconnect installed and running, but I wanted to try Astaro.

I burned the install CD and tried installing, but it never gets to the point of booting. 

Loading bzimage

Loading initrd

Ready.


And it reboots here, with no error messages or anything. I've tried all three methods of install, , classic and nosmp; they all produce the same results.

I have an Intel, rackmount server chassis with a L440GX+ mainboard with dual PIII 500s with 512mb ECC ram.

Is the hardware listed on the HCL the ONLY supported hardware?


This thread was automatically locked due to age.
Parents
  • 0
    Ok, so.... I'm not sure what's happening here. I have Clarkconnect installed and running, but I wanted to try Astaro.

    I burned the install CD and tried installing, but it never gets to the point of booting.

    Loading bzimage
    Loading initrd
    Ready.
    And it reboots here, with no error messages or anything. I've tried all three methods of install, , classic and nosmp; they all produce the same results.

    I have an Intel, rackmount server chassis with a L440GX+ mainboard with dual PIII 500s with 512mb ECC ram.

    Is the hardware listed on the HCL the ONLY supported hardware?

    no that's the only hardware Astaro has tested.  My setup isn't certified but it runs fine.  Try installing in classic mode.

    Owner:  Emmanuel Technology Consulting

    http://etc-md.com

    Former Sophos SG(Astaro) advocate/researcher/Silver Partner

    PfSense w/Suricata, ntopng, 

    Other addons to follow

  • 0 in reply to William Warren
    when installing try  or  to see some logs.
  • 0 in reply to bitonw
    when installing try  or  to see some logs.


    I don't even get to the install screen, only the 'flavor' screen where you pick which install you want to run.
  • 0 in reply to ShadowLab
    the  screens should show up regardless, unless your graphics adapter is totally unsupported... try a different video card (nothing fancy is needed).

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • 0 in reply to BrucekConvergent
    I might add, make sure there is only ONE CDROM Drive, and only ONE Hard drive in the system... Astaro software will not install properly with "too many" drives in the system.

    CTO, Convergent Information Security Solutions, LLC

    https://www.convergesecurity.com

    Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries.  Use the advice given at your own risk.

  • 0 in reply to BrucekConvergent
    Burning/trying another ASL-Versions (older) can sometimes help. 

    Gregor Kemter
  • 0 in reply to gkemter
    Well, looks like there's some sort of other issue also. Out of interest, I tried loading the gentoo CD and it does the same thing. I think CC only works because of the new kernel used on it.

    This hardware has had issues in the past with the Adaptec SCSI driver.

    Oh well, at least I have one distro that'll run :/
Reply
  • 0 in reply to gkemter
    Well, looks like there's some sort of other issue also. Out of interest, I tried loading the gentoo CD and it does the same thing. I think CC only works because of the new kernel used on it.

    This hardware has had issues in the past with the Adaptec SCSI driver.

    Oh well, at least I have one distro that'll run :/
Children
Cookie Information Banner