This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Will this hardware work with V7?

Hi all,
I would like to use the following hardware for V7.

Asus M2N-SLI Deluxe // Athlon64 3800 // 1024GB
PCI (32 Bit)  3 // 33 MHz
PCIe x1  2
PCIe x16  2

with 3 piece Intel Pro/1000MT Pro PCIx (64bit)

Would be important to know whether the three Intel NIC work.

Thanks for each assistance / hints.

Stefan

This thread was automatically locked due to age.

Parents

0 StefanS_01 over 18 years ago

Hi Berry,
>>1TB RAM? pretty good
Ups, 1GB (although 1T would already be a hot box).

>>What kind of HD controller
standard IDE. Unfortunately SATA is not supported (Nvidia etc.).

Stefan
Cancel
Vote Up 0 Vote Down

Cancel
0 SilverOne over 18 years ago in reply to StefanS_01

Hi SteFanS,

Nice gaming board bye the way....

The Nforce (Nvidia chip) is not supported see:http://www.astaro.com/lists/HCL-ASG-V7.txt
you can find al the tested hardware in that list, it is a OLD list.
Hardware listed older than 1 year....
Cancel
Vote Up 0 Vote Down

Cancel
0 lantech over 18 years ago in reply to SilverOne

I found the v7.001 works with a whole lot more hardware than it did as a beta. Best bet is to just try and install it. Sometimes faster than trying to decipher the tested hardware lists.
Cancel
Vote Up 0 Vote Down

Cancel
0 drees over 18 years ago in reply to lantech

I found the v7.001 works with a whole lot more hardware than it did as a beta. Best bet is to just try and install it. Sometimes faster than trying to decipher the tested hardware lists.

Yep, and if it does work, be sure to report back. [:)]

Would be nice if Astaro collected actual hardware info and then built their HCL from that.

Something like the Fedora smolt project:
https://hosted.fedoraproject.org/projects/smolt/wiki
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 drees over 18 years ago in reply to lantech

I found the v7.001 works with a whole lot more hardware than it did as a beta. Best bet is to just try and install it. Sometimes faster than trying to decipher the tested hardware lists.

Yep, and if it does work, be sure to report back. [:)]

Would be nice if Astaro collected actual hardware info and then built their HCL from that.

Something like the Fedora smolt project:
https://hosted.fedoraproject.org/projects/smolt/wiki
Cancel
Vote Up 0 Vote Down

Cancel

Children

0 StefanS_01 over 18 years ago in reply to drees

Hi all,

Similarly as here, only GRUB starts and then the system freezes.

https://community.sophos.com/products/unified-threat-management/astaroorg/f/52/t/25926

Installs OK, however none reboot.
All the same whether with a IDE or a SATA HDD.

The chipset from the Motherboard is also in the HCL.
Does someone have idea?

Chers

Stefan
Cancel
Vote Up 0 Vote Down

Cancel
0 StefanS_01 over 18 years ago in reply to StefanS_01

Property now a test with the 6.3 version started.
Everything works without problems.
Cancel
Vote Up 0 Vote Down

Cancel
0 StefanS_01 over 18 years ago in reply to StefanS_01

Error found.
ASL forgets to start with noapic.
After which i registered the following option in GRUB,

nolapic noapic apci=off

the ASL without problems starts.
ASL was installed with the option "classic".

Cheers

Stefan
Cancel
Vote Up 0 Vote Down

Cancel