[7.450][QUESTION][ANSWERED] Dashboard does not show correct interface status

Hi friends !

dash board doesnt show correct status of interface (link and state )

even i adsl modem is off it show up
and even the interface cable is unpluged it show link

ifplugstatus

Thanks

Parents

0 Billybob over 16 years ago

It is working fine for me. Don't unplug the lan interface if you are using webadmin from Lan interface since it can't show you the correct status[:D]

I tried it on my dmz and WAN and it shows link down state up which is correct.
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

0 Astaro Beta Bot over 16 years ago in reply to Billybob

Astaro Beta Report
--------------------------------
Version: 7.450
Type: QUESTION
State: ANSWERED
Reporter: utm_kid
Contributor: 
MantisID: 
--------------------------------

0 andyk007 over 16 years ago in reply to utm_kid

OK, regarding to your screenshot.

this was a result if you create all dummy vlan interface which are not connected to any switch and there was no cable connected to eth0?
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 utm_kid over 16 years ago in reply to andyk007

OK, regarding to your screenshot.

this was a result if you create all dummy vlan interface which are not connected to any switch and there was no cable connected to eth0?

Yes ,

That right

Thanks
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 andyk007 over 16 years ago in reply to andyk007

I cannot reproduce it with 7.460. I took eth3 and created 3 non existing vlans. There is no physically link on eth3 and I get the correct view in the dashboard. state up and all links down
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 utm_kid over 16 years ago in reply to andyk007

I cannot reproduce it with 7.460. I took eth3 and created 3 non existing vlans. There is no physically link on eth3 and I get the correct view in the dashboard. state up and all links down

Hi !

please check new image ,did u refresh ,logout and login again

Thanks
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 andyk007 over 16 years ago in reply to utm_kid

I rebooted the ASG, login/logout of webadmin and no problem exist. Could you please give me the output of ethtool eth1?

Greetings
Andreas
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 utm_kid over 16 years ago in reply to andyk007

I rebooted the ASG, login/logout of webadmin and no problem exist. Could you please give me the output of ethtool eth1?

Greetings
Andreas

Hi ,

# ethtool eth1
Settings for eth1:
        Supported ports: [ TP MII ]
        Supported link modes:   10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Supports auto-negotiation: Yes
        Advertised link modes:  10baseT/Half 10baseT/Full
                                100baseT/Half 100baseT/Full
        Advertised auto-negotiation: Yes
        Speed: 100Mb/s
        Duplex: Full
        Port: MII
        PHYAD: 24
        Transceiver: internal
        Auto-negotiation: on
        Current message level: 0x00000001 (1)
        Link detected: yes
ace75:/home/login #
Thanks
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 andyk007 over 16 years ago in reply to utm_kid

OK you have a cable connected to eth port :

Link detected: yes

I asked you two times if you have a physically connect. So this is definitely no bug

Greetings
Andreas
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 utm_kid over 16 years ago in reply to andyk007

OK you have a cable connected to eth port :

Link detected: yes

I asked you two times if you have a physically connect. So this is definitely no bug

Greetings
Andreas

Ok ,i change the card/reconfigure but didnt change cable i will do that and check again ,do u see hardware (HCL) issue

Thanks
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 andyk007 over 16 years ago in reply to utm_kid

other question what is in your oppinion wrong? If a cable is connected to the ethernet port you will always have link = up. Thats since Version 7.000 ;-)

Greetings
Andreas
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel
0 utm_kid over 16 years ago in reply to andyk007

other question what is in your oppinion wrong? If a cable is connected to the ethernet port you will always have link = up. Thats since Version 7.000 ;-)

Greetings
Andreas

pls check image

on vlan interface cable is not connect still it says connected ?
internal interface error

when u add vlan interface in uplink till u configure it look like a ok but when u click aply it goes in red
(dear friend last try to convince u or may be some hardware issues/hcl )
upload (please see image )is different issue ?

is this process i lost gw of external interface every time
Thanks
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Reply

0 utm_kid over 16 years ago in reply to andyk007

other question what is in your oppinion wrong? If a cable is connected to the ethernet port you will always have link = up. Thats since Version 7.000 ;-)

Greetings
Andreas

pls check image

on vlan interface cable is not connect still it says connected ?
internal interface error

when u add vlan interface in uplink till u configure it look like a ok but when u click aply it goes in red
(dear friend last try to convince u or may be some hardware issues/hcl )
upload (please see image )is different issue ?

is this process i lost gw of external interface every time
Thanks
Cancel
Vote Up 0 Vote Down

Sign in to reply

Verify Answer

Cancel

Children

No Data