This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Supermicro E300-12C Sophos Home Build

Built a new Supermicro E300-12C setup with a i3 and dual 10gbe SPF+ NIC card. Went to boot to USB and it hangs when trying to install immediately. After many hours of searching I have come to the conclusion as many where it does not seems UEFI Bios systems are compatible with Sophos XG Home setups. Unfortunately the bird cannot boot to legacy bios so I’m stuck at where to go from here. Has anyone had any luck at all installing or running XG Home on a UEFI system?

This thread was automatically locked due to age.

Top Replies

rfcat_vk over 3 years ago in reply to Joshua Ewing +1

Hiii Joshua, in theory all the NICs will be available to your XG through the VM. I would recommend you install the XG on the vm using the ISO you already have. XG does not recognise i219 series NICs…

Parents

0 rfcat_vk over 3 years ago

Hi,

does there BIOS have a non UEFI option. If you have another motherboard with a none UEFI BIOS you could install to that then move the disk to your preferred device or even build a temporary VM. A further issue will be your NICs, one of the onboard ones is not compatible with XG and the 10gbe NICs, how have yo determined they are compatible.

Your best bet would be to build a VM and install the XG on that. I have not found SuperMicro MBs to be very convertible with XG or the UTM in the past, the leave out see timing hardware.

Ian
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 rfcat_vk over 3 years ago

Hi,

does there BIOS have a non UEFI option. If you have another motherboard with a none UEFI BIOS you could install to that then move the disk to your preferred device or even build a temporary VM. A further issue will be your NICs, one of the onboard ones is not compatible with XG and the 10gbe NICs, how have yo determined they are compatible.

Your best bet would be to build a VM and install the XG on that. I have not found SuperMicro MBs to be very convertible with XG or the UTM in the past, the leave out see timing hardware.

Ian
Cancel
Vote Up 0 Vote Down

Cancel

Children

0 Joshua Ewing over 3 years ago in reply to rfcat_vk

Thanks Ian.

Confirmed my MB is ONLY UEFI.

I really have no idea if the NIC card is compatible or not as I didn’t even think that would be an issue. Here is the card.

10Gb SFP+ PCI-E Network Card NIC, with Broadcom BCM57810S Chip, Dual SFP+ Port, PCI Express X8, Support Windows Server /Linux/VMware https://www.amazon.com/dp/B06X9T683K/ref=cm_sw_r_cp_api_glt_fabc_MD3JJ7ZZ9A0WKKWMRCC2?_encoding=UTF8&psc=1

also decided I may be better off installing vSphere Hypervisor from VMware and then downloading the XG Home VMware image and going that route.
Cancel
Vote Up 0 Vote Down

Cancel
0 rfcat_vk over 3 years ago in reply to Joshua Ewing

Hiii Joshua,

in theory all the NICs will be available to your XG through the VM. I would recommend you install the XG on the vm using the ISO you already have. XG does not recognise i219 series NICs.

Ian
Cancel
Vote Up +1 Vote Down

Cancel
0 Joshua Ewing over 3 years ago in reply to rfcat_vk

Thank you very much for the guidance here. I have been researching and trying to configure my Virtual Switch's / Port Groups / Physical NICs appropriately. I know I need to configure Switch's correctly but need some help as I am a NEWB to this. I put together a few docs to convey where I currently sit.

Any Help is greatly appreciatedNetworking MAP.pdf Current ESXi 7.0 Networking TABs.pdf
Cancel
Vote Up 0 Vote Down

Cancel