This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

SLL VPN - MacOS X Problem reaching remote network

Hello
I'm using Tunnelblick to connect via SSL VPN to my network at home.

The SLL VPN comes up correctly but I'm not able to reach any of the devices on the other end of the tunnel.

Config local:

WLAN with 192.168.1.x IPs

Config remote:

LAN with 192.168.0.x
WAN @ 192.168.1.x (with Fritzbox as router)
SSL VPN IPs @ 192.168.2.x

SSL VPN configured to be able to reach LAN (auto. packet filter)

When trying traceroute to the remote LAN the packet first goes to the WLAN router then getting lost somewhere in the web.

Anyone an idea?

I need the tunnel to access remote smb shares and servers.

greetz chaser

This thread was automatically locked due to age.

0 BarryG over 15 years ago

Hi, do you have Masquerading and PacketFilter rules setup for the SSL VPN pool?

Barry
Cancel
Vote Up 0 Vote Down

Cancel
0 r2k over 15 years ago

Do you run snow leopard on 64bit?

Marco
Cancel
Vote Up 0 Vote Down

Cancel
0 IngoPohlschneider over 15 years ago

Hello
yes I'm using SnowLeopard @64bit

Who should the masquerading be configured?

Are packet filter rules still needed even if "Automatic packet filter rule" is enabled in General Tab @ Remote Access page?

Greetz chaser
Cancel
Vote Up 0 Vote Down

Cancel
0 r2k over 15 years ago

try to boot with the 32bit kernel.
under 64 bit it will not work.

otherwise try tunnelblick with this extensions: Snow Leopard 64bit + Tunnelblick (tuntap) | jamit.de

masquerading is used, because your vpn client is in another network then the internal clients
Cancel
Vote Up 0 Vote Down

Cancel
0 IngoPohlschneider over 15 years ago

In the activity monitor I see the tunnelblick to be running as 32bit process.

by "Who" I meand "how should masquerading be configured"

Currently there are two rules:

LAN -> WAN
SSL VPN Adresspool -> LAN
Cancel
Vote Up 0 Vote Down

Cancel
0 BarryG over 15 years ago in reply to IngoPohlschneider

Currently there are two rules:

LAN -> WAN
SSL VPN Adresspool -> LAN

Hi, if those are your Masquerading settings, they should be

LAN -> WAN
SSL VPN Adresspool -> WAN

Barry
Cancel
Vote Up 0 Vote Down

Cancel
0 IngoPohlschneider over 15 years ago

Hello
ok, did so but even this configuration of the Masquerading isn't solving my problems

Greetz chaser
Cancel
Vote Up 0 Vote Down

Cancel
0 jtarnoff over 15 years ago

This doesn't directly address your issue, but have you tried using Viscosity (Viscosity - OpenVPN Client for Mac) rather than TunnelBrick? Works perfectly on Snow Leopard 64 bit, and while not free--pretty inexpensive.
Cancel
Vote Up 0 Vote Down

Cancel
0 eganders_01 over 15 years ago in reply to jtarnoff

This doesn't directly address your issue, but have you tried using Viscosity (Viscosity - OpenVPN Client for Mac) rather than TunnelBrick? Works perfectly on Snow Leopard 64 bit, and while not free--pretty inexpensive.

I think it's $9. Plus you get it free for a trial period so you can see if it will work for you.
Cancel
Vote Up 0 Vote Down

Cancel
0 warper over 15 years ago in reply to eganders_01

I am running tunnelblick just fine here on osx 10.6 64 bit. Just set it up on Friday and it works fine.
Cancel
Vote Up 0 Vote Down

Cancel