This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Vista + PPTP

ASG220 + 7.007

I have Vista (ugh). PPTP connections just don't work - sometimes authentication fails, sometimes works then after a few minutes traffic ceases and the PPTP daemon complains about misordered packets etc. etc.. On my XP laptop PPTP works like a charm.

I think I have butchered every single Vista PPTP config setting in an attempt to get it to work (eg. force PAP, disable IPv6, force PPTP etc. etc.)

Anyone got a definitive guide on how to make it work reliably?

TIA


This thread was automatically locked due to age.
Parents
  • I just left mine at the defaults and have had no problems connecting from a Vista Ultimate system to my v6 ASG firewall at work.  No drops, can access everything, no issues at all.  I have two seperate systems running Vista Ultimate at home and both connect just fine.
Reply
  • I just left mine at the defaults and have had no problems connecting from a Vista Ultimate system to my v6 ASG firewall at work.  No drops, can access everything, no issues at all.  I have two seperate systems running Vista Ultimate at home and both connect just fine.
Children
  • I've got the issue on v7 not v6 ...
  • James, 

    Silly question, but our your default gateway settings on the machine / network routing back to the ASG?

    Did you have it working in 7.006?

    Please can you post your connection ASG & client logs

    well minus any senseative stuff of course

    cheers
  • I've never got it to work Mike [:(] I've got two Vista boxes: Enterprise and Ultimate. One's an IBM laptop the other a desktop. No dice with Fista. I've tried with 7.007, 7.008 and 7.009. Can't remember with 7.006 [;)]

    However Win XP SP2 works like a charm.

    The private network on this side is: 172.168.1.0/24 and on the other end is 192.168.2.0/24.

    Vista routing is as follows:

    Network Destination        Netmask          Gateway       Interface  Metric
              0.0.0.0          0.0.0.0     172.16.1.254     172.16.1.104   4235
              0.0.0.0          0.0.0.0         On-link        10.242.1.2     11

    Lower metric indicates data should be stuffed down the tunnel.

    Here's some logs (I've put an Any/Any/Any rule in the packet filter just to be sure) but I see no traffic getting to devices on the otherside:

    2007:09:16-15:27:27 (none) pptpd[5411]: CTRL: Starting call (launching pppd, opening GRE)
    2007:09:16-15:27:27 (none) pppd-pptp[5412]: Plugin /usr/sbin/aua.so loaded.
    2007:09:16-15:27:27 (none) pppd-pptp[5412]: AUA plugin initialized.
    2007:09:16-15:27:27 (none) pppd-pptp[5412]: Plugin /usr/sbin/aua.so loaded.
    2007:09:16-15:27:27 (none) pppd-pptp[5412]: AUA plugin initialized.
    2007:09:16-15:27:27 (none) pppd-pptp[5412]: pppd 2.4.3 started by (unknown), uid 0
    2007:09:16-15:27:27 (none) pppd-pptp[5412]: Starting negotiation on /dev/ttyp0
    2007:09:16-15:27:27 (none) pptpd[5411]: GRE: Bad checksum from pppd.
    2007:09:16-15:27:31 (none) pptpd[5411]: CTRL: Ignored a SET LINK INFO packet with real ACCMs!
    2007:09:16-15:27:33 (none) pppd-pptp[5412]: Using interface ppp0
    2007:09:16-15:27:33 (none) pppd-pptp[5412]: Cannot determine ethernet address for proxy ARP
    2007:09:16-15:27:33 (none) pppd-pptp[5412]: local IP address 10.242.1.1
    2007:09:16-15:27:33 (none) pppd-pptp[5412]: remote IP address 10.242.1.2
    2007:09:16-15:27:33 (none) pppd-pptp[5412]: MPPE 128-bit stateless compression enabled
    2007:09:16-15:27:33 (none) pppd-pptp[5420]: id="2201" severity="info" sys="SecureNet" sub="vpn" event="Connection started" username="jbourne" variant="pptp" srcip="x.x.x.x" virtual_ip="10.242.1.2" 

    I also see this at the Astaro end in the routing table:

    10.242.2.2 dev tun0  proto kernel  scope link  src 10.242.2.1