This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

IPSEC between ASL 5 and Cisco 827

Has anyone got a IPSEC vpn working between a CISCO 827/837 DSL router and ASL5. Any sample Cisco config's would be much appreciated.
[:O]

This thread was automatically locked due to age.

Parents

0 Para over 20 years ago

I'm having the same problems!!
Is there anyone who can come up wit a working cisco config?
Cancel
Vote Up 0 Vote Down

Cancel
0 NimmdirKeks over 20 years ago in reply to Para

Hi,

sorry to say, but with all the exp. i have with those ciscos it wont work.
Because: "Cisco, we are the STANDARD"

Chris
Cancel
Vote Up 0 Vote Down

Cancel
0 ZaD80 over 20 years ago in reply to NimmdirKeks

Nearly same problem, trying to connect ASL 5 and CISCO 801.

searching for some sample configs.
Cancel
Vote Up 0 Vote Down

Cancel
0 ClausP over 20 years ago in reply to ZaD80

... this is a nice basic config ! [;)]
Cancel
Vote Up 0 Vote Down

Cancel

Reply

0 ClausP over 20 years ago in reply to ZaD80

... this is a nice basic config ! [;)]
Cancel
Vote Up 0 Vote Down

Cancel

Children

0 ZaD80 over 20 years ago in reply to ClausP

I have trouble with IKE phase 1, I got INVALID_ID_INFORMATION because of the CISCO 801 has a dynamic IP. But Astaro needs IPv4_ID and i don't know how! Had same porblem with software Netways, but finally found where i could enter the virtual IP, defined in PSK. If sombody know how to do that with CISCO, please let me know.

Thx

pluto[11232]: packet from DYN_IP:500: ignoring Vendor ID payload [439b59f8ba676c4c...]
pluto[11232]: packet from DYN_IP:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03]
pluto[11232]: packet from DYN_IP:500: ignoring Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n]
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: responding to Main Mode from unknown peer DYN_IP
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: transition from state (null) to state STATE_MAIN_R1
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: ignoring Vendor ID payload [Cisco-Unity]
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: received Vendor ID payload [Dead Peer Detection]
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: ignoring Vendor ID payload [32c71f33c89cb16d...]
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: ignoring Vendor ID payload [XAUTH]
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: NAT-Traversal: Result using draft-ietf-ipsec-nat-t-ike-02/03: no NAT detected
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: transition from state STATE_MAIN_R1 to state STATE_MAIN_R2
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: ignoring informational payload, type IPSEC_INITIAL_CONTACT
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: Main mode peer ID is ID_IPV4_ADDR: 'DYN_IP'
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: transition from state STATE_MAIN_R2 to state STATE_MAIN_R3
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: sent MR3, ISAKMP SA established
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: cannot respond to IPsec SA request because no connection is known for 10.5.27.0/24===static_IP_Astaro...DYN_IP===192.168.1.0/24
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: sending encrypted notification INVALID_ID_INFORMATION to DYN_IP:500
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP #13: received Delete SA payload: deleting ISAKMP State #13
pluto[11232]: "S_Roadwarrior_0"[7] DYN_IP: deleting connection "S_Roadwarrior_0" instance with peer DYN_IP
pluto[11232]: packet from DYN_IP:500: received and ignored informational message
Cancel
Vote Up 0 Vote Down

Cancel