Guest User!

You are not Sophos Staff.

This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Astaro and PGPNet for VPN

I'm trying to setup a VPN to my Astaro box, and I'm reading the documentation and it says to use PGP version 7.0.4.  But according to the PGP homepage 7.0.3 is the latest free version.  Plus the screen shots show different configuration screens that I have.  Where can I get 7.0.4, or what is different with 7.0.3?

[ 10 January 2002: Message edited by: Scotty Baker ]



This thread was automatically locked due to age.
Parents
  • I have the same problem. I can't define a gateway on PGPFW7.0.3. Now I'm trying SSH Sentinel.
  • There is no additionnal gateway... The Security Association encapsulate the packet. If you followed the instructions properly with docs.astaro.org / VPN howto .. you are good to go make sure you define a Insecure network which is a real network behind your IPSEC gateway (ASL). 

    Make sure also that host on the network have their default route to the IPSEC gateway..

    Patrice.

    I used PGPNet 7.0.3.

    *Note* Make sure you run Setadapter from PGPNEt to secure at least your adapter you are using to connect to the Internet... Make sure also that PGPNet is enabled.

    [ 18 January 2002: Message edited by: TnM ]

    [ 18 January 2002: Message edited by: TnM ]

  • Apr 1 08:52:51 asl Pluto[16464]:"pgp_1" #103: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0xa6f4dbc5 (perhaps this is a duplicated packet) 
    Apr 1 08:53:06 asl Pluto[16464]:"pgp_1" #103: ignoring Delete SA payload 
    Apr 1 08:53:06 asl Pluto[16464]:"pgp_1" #103: received and ignored informational message 
    Apr 1 08:53:30 asl Pluto[16464]:"pgp_1" #105: STATE_MAIN_R3: sent MR3, ISAKMP SA established 
    Apr 1 08:53:30 asl Pluto[16464]:"pgp_1" #105: ignoring informational payload, type IPSEC_INITIAL_CONTACT 
    Apr 1 08:53:30 asl Pluto[16464]:"pgp_1" #105: responding to Main Mode from unknown peer 61.165.223.200 
    Apr 1 08:53:30 asl Pluto[16464]:"pgp_1" #106: cannot respond to IPsec SA request because no connection is known for 61.152.125.82...61.165.223.200 
    Apr 1 08:53:30 asl Pluto[16464]   acket from 61.165.223.200:500: ignoring Vendor ID payload 
    Apr 1 08:53:32 asl Pluto[16464]:"pgp_1" #105: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0xddabde7f (perhaps this is a duplicated packet) 
    Apr 1 08:53:43 asl Pluto[16464]:"pgp_1" #105: ignoring Delete SA payload 
    Apr 1 08:53:43 asl Pluto[16464]:"pgp_1" #105: received and ignored informational message 


    i use pgpnet 7.0.3,but bug up appears,help me !!
    i use dynamic address(dial).
Reply
  • Apr 1 08:52:51 asl Pluto[16464]:"pgp_1" #103: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0xa6f4dbc5 (perhaps this is a duplicated packet) 
    Apr 1 08:53:06 asl Pluto[16464]:"pgp_1" #103: ignoring Delete SA payload 
    Apr 1 08:53:06 asl Pluto[16464]:"pgp_1" #103: received and ignored informational message 
    Apr 1 08:53:30 asl Pluto[16464]:"pgp_1" #105: STATE_MAIN_R3: sent MR3, ISAKMP SA established 
    Apr 1 08:53:30 asl Pluto[16464]:"pgp_1" #105: ignoring informational payload, type IPSEC_INITIAL_CONTACT 
    Apr 1 08:53:30 asl Pluto[16464]:"pgp_1" #105: responding to Main Mode from unknown peer 61.165.223.200 
    Apr 1 08:53:30 asl Pluto[16464]:"pgp_1" #106: cannot respond to IPsec SA request because no connection is known for 61.152.125.82...61.165.223.200 
    Apr 1 08:53:30 asl Pluto[16464]   acket from 61.165.223.200:500: ignoring Vendor ID payload 
    Apr 1 08:53:32 asl Pluto[16464]:"pgp_1" #105: Quick Mode I1 message is unacceptable because it uses a previously used Message ID 0xddabde7f (perhaps this is a duplicated packet) 
    Apr 1 08:53:43 asl Pluto[16464]:"pgp_1" #105: ignoring Delete SA payload 
    Apr 1 08:53:43 asl Pluto[16464]:"pgp_1" #105: received and ignored informational message 


    i use pgpnet 7.0.3,but bug up appears,help me !!
    i use dynamic address(dial).
Children