Guest User!

You are not Sophos Staff.

This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Beginner Question: Multipath Rules & QoS

Hi Guys,

I am just an amateur (so excuse the post), and starting to really like the features of Sophos UTM.

But because I'm not a professional I really do find it hard to understand how to operate it correctly. I can read the user manual but without live examples I find it very hard to relate to my (personal) setup.

I have got two WANS and one LAN.  The WANS are slow ADSL connections which is all we can get here.  Auto balancing is enabled.  Off it I am running 10 PCs, a Voip server , 5 Cisco voip handsets, 6 smart phones, 2 laptops, and a partridge in a pear tree.

My troubles are as follows:

Question
I have to configure a multpath rule so VOIP only runs through one of the WANs.  I dont understand "what to put where" in the multipath rules. A bit of advice would be appreciated.   I'm running a VOIP PBX called 3CX on PC 192.168.1.2 and it uses ports 5060(sip) and also 9000:9014 (rtp) to operate, and it has to go down one wan, not both or either.

Pls advise correct parameters for the multipath rule:
SOURCE:?
SERVICE: (I assume the port)?
DESTINATION:?
ADVANCED: BALANCE TO: (assume WAN1)?



Thanks guys -you're the best. [:)]

Cheers
Noddy


This thread was automatically locked due to age.
2013-05-28 21_06_25-Microsoft Excel - wan & QOS config.zip
Parents
  • Here is the screenshot I have of my position 7 (bottom of list) multipath rule for voip, which seems to work well. However I don't have any other rules set as yet, and the ones that are there by default are unchecked.

    Furthermore, I noticed an issue when setting an (additional) rule called 'any to any' as you suggested.  I had it in position 1, (the lowest priority?), and when enabled, it would stuff up position 7 (Voip) (the highest priority) which I found unusual, as i thought according to the manual, it wouldnt do that? (I assume the problem is because it is conflicting request.. in position 7 rule you say send ports 5060 & 9000:9014 to wan 1 only, but in position 1 rule you say send any ports to either wan?)  Anyway I disabled the 'any to any' rule.


    I've attached a diagram of all the rules i'd like to add eventually once I understand the configuration method.

    If I get the Rule 1 (all devices except server to use Wan2) out of the way first, then I suppose i can configure the remaining rules for my server 192.168.1.2 as listed in the attachment.
Reply
  • Here is the screenshot I have of my position 7 (bottom of list) multipath rule for voip, which seems to work well. However I don't have any other rules set as yet, and the ones that are there by default are unchecked.

    Furthermore, I noticed an issue when setting an (additional) rule called 'any to any' as you suggested.  I had it in position 1, (the lowest priority?), and when enabled, it would stuff up position 7 (Voip) (the highest priority) which I found unusual, as i thought according to the manual, it wouldnt do that? (I assume the problem is because it is conflicting request.. in position 7 rule you say send ports 5060 & 9000:9014 to wan 1 only, but in position 1 rule you say send any ports to either wan?)  Anyway I disabled the 'any to any' rule.


    I've attached a diagram of all the rules i'd like to add eventually once I understand the configuration method.

    If I get the Rule 1 (all devices except server to use Wan2) out of the way first, then I suppose i can configure the remaining rules for my server 192.168.1.2 as listed in the attachment.
Children
No Data