Guest User!

You are not Sophos Staff.

This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

[8.0001] PPPOE Connection Terminates after 0.3seconds

Hi Everyone

IBM e326M
3 Network Cards
1 Configured Interal
1 Configured for PPPOE
1 Spare

Just upgraded our firewall from v7 to v8. I have a beklin router (ISP is iiNET Australia) setup with default settings and upgraded to latest firmware patch. I have not configured the modem to connect to the internet (PPPOE). It is set to default settings.

I've setup a PPPOE connection as follows :
Name:  External Wan
Type: DSL (PPPOA / PPTP) Ethernet StandardCable Modem (DHCP)DSL (PPPOE)Modem (PPP)Ethernet VLAN 
Hardware: eth2 (Intel Corporation 82544EI Gigabit Ethernet Controller (Copper)) 
VDSL:  
Static PPPOE IP:  
IPv4 Default GW:  Checked
Username: ************
Password: ************ 
Daily reconnect: :: Please select ::
Reconnect Delay: 5 seconds
MTU:  1492
Asymmetric  
Displayed max  
 kbpsMbps 
Comment:  

The problem is that it seems to work but disconnects. Here is the PPPOE Log :
PAP authentication succeeded 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: peer from calling number 00:30:88:17:47:09 authorized 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: sent [IPCP ConfReq id=0x1   ] 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: rcvd [IPCP ConfReq id=0x61 ] 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: sent [IPCP ConfAck id=0x61 ] 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: rcvd [IPCP ConfNak id=0x1   ] 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: sent [IPCP ConfReq id=0x2   ] 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: rcvd [IPCP ConfAck id=0x2   ] 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: local IP address 203.173.x.x 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: remote IP address 203.215.x.x
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: primary DNS address 203.0.178.x
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: secondary DNS address 203.215.29.x 
2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: Script /etc/ppp/ip-up started (pid 18378) 

It stops here for about 3 seconds than...

2010:07:31-12:54:21 ICE-FIREWALL pppd-pppoe[18376]: Script /etc/ppp/ip-up finished (pid 18378), status = 0x0 
2010:07:31-12:54:36 ICE-FIREWALL pppd-pppoe[18376]: Hangup (SIGHUP) 
2010:07:31-12:54:36 ICE-FIREWALL pppd-pppoe[18376]: Connect time 0.3 minutes. 
2010:07:31-12:54:36 ICE-FIREWALL pppd-pppoe[18376]: Sent 33729 bytes, received 85200 bytes. 
2010:07:31-12:54:36 ICE-FIREWALL pppd-pppoe[18376]: Script /etc/ppp/ip-down started (pid 18589) 
2010:07:31-12:54:36 ICE-FIREWALL pppd-pppoe[18376]: sent [LCP TermReq id=0x2 "User request"] 
2010:07:31-12:54:36 ICE-FIREWALL pppd-pppoe[18376]: Modem hangup 
2010:07:31-12:54:36 ICE-FIREWALL pppd-pppoe[18376]: Connection terminated. 

I've contact my ISP and asked them to do line test and port reset at the exchange. Was working fine in v7... seems to be the upgrade? 

Any ideas? Currently my work around is to configure the Beklin Modem to PPPOE out. Than i've setup a DMZ to map the external address given by my ISP to the internal address of the 1 spare network card (Beklin is 10.1.1.1 and the spare is 10.1.1.5). Than create another interface in Astaro using Ethernet Standard as the type. Gives me access.... 

However, I have 3 internal web servers all on seperate servers (was quite excited to see WAS in v8). External access in isn't working like it should and i fear its because my external address is seen as 10.1.1.5 as apposed to a PPPOE address.....

Your genius help is much anticipated [:)]


This thread was automatically locked due to age.
Parents
  • Hi,
    welcome aboard.
    What mode do you have your modem set in?

    It should be in bridge mode, I can't remember the exact RFC settings.

    I have found the iinet belkin equipment to be very limited in functionality and configuration. I still can't get the iinet belkin VoIP adapter to savfe its configuration correctly. It is close, but not 100% the way I want it.

    You might be better off buying a netgear or billion cheap router/modem.

    Ian M
  • Hi

    Thanks for the response and the welcome.

    I will give it a bash this weekend and let you know. I've worked with Netgear Router/Modems in the past and they had a "backend" homepage where you could switch the Router to Modem Only which helps in cases like this... Can't seem to find it for Beklin.

    I agree. Beklin's seem very limited.

    Will let you know.
Reply
  • Hi

    Thanks for the response and the welcome.

    I will give it a bash this weekend and let you know. I've worked with Netgear Router/Modems in the past and they had a "backend" homepage where you could switch the Router to Modem Only which helps in cases like this... Can't seem to find it for Beklin.

    I agree. Beklin's seem very limited.

    Will let you know.
Children