Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 13 replies
  • Subscribers 2 subscribers
  • Views 8736 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

hardware temperatures

Crisman
Hi,

Since in my country we are in high season the weather temperatures are going high, sometimes inside office around 27 ºC, yes really high!  so I would like to monitor the temperartures regulary of my UTM hardware (CPU, Hard drive), is there any way to do that like running a script or linux command? [:(]

Thanks.


This thread was automatically locked due to age.
  • 0
    If you login via SSH (Loginuser) you can get sensor values with "sensors". On a UTM425 appliance:
    > sensors
    coretemp-isa-0000
    Adapter: ISA adapter
    Physical id 0:  +39.0°C  (high = +80.0°C, crit = +99.0°C)
    Core 0:         +36.0°C  (high = +80.0°C, crit = +99.0°C)
    Core 1:         +35.0°C  (high = +80.0°C, crit = +99.0°C)
    Core 2:         +38.0°C  (high = +80.0°C, crit = +99.0°C)
    Core 3:         +39.0°C  (high = +80.0°C, crit = +99.0°C)


    Only CPU cores, but better than nothing. You may also can get temp values from SNMP. Never tried.
  • 0
    A start might be:
    sensors

    and  (root required)
    # smartctl -a /dev/sda


    I have not checked to see if the UTM shares temperature data via SNMP.
  • 0
    OK guys!

    I will test those commands when get at home.

    Thanks.
  • 0
    Hi,

    I've tested those commands and the results are: 

    loginuser@utm9-lan:/home/login > sensors

    acpitz-virtual-0

    Adapter: Virtual device

    temp1:        +27.8°C  (crit = +92.0°C)

    temp2:        +29.8°C  (crit = +92.0°C)

    

    coretemp-isa-0000

    Adapter: ISA adapter

    Physical id 0:  +45.0°C  (high = +87.0°C, crit = +91.0°C)

    Core 0:         +45.0°C  (high = +87.0°C, crit = +91.0°C)

    Core 1:         +44.0°C  (high = +87.0°C, crit = +91.0°C)


    and the smartctl command: 

    loginuser@utm9-lan:/home/login > smartctl -i -a /dev/sda

    -bash: smartctl: command not found

    loginuser@utm9-lan:/home/login >
  • 0
    Try that second command as root.

    Cheers - Bob
  • 0
    It will likely be beneficial to configure your system with sensors-detect (or editing /etc/sysconfig/lm_sensors.conf) and editing /etc/sensors3.conf for the appropriate values. 

    # sensors-detect


    sensors3.conf configurations for many boards are at http://www.lm-sensors.org/wiki/Configurations

    My previous post has been updated to better reflect the need for root.
  • 0
    Hi, 

    I run the command as root and result is the same.

    loginuser@utm9-lan:/home/login > sudo smartctl -a /dev/sda

    We trust you have received the usual lecture from the local System
    Administrator. It usually boils down to these three things:

        #1) Respect the privacy of others.
        #2) Think before you type.
        #3) With great power comes great responsibility.

    root's password:
    sudo: smartctl: command not found
  • 0
    Please try with su - and then run the command in the root environment.

    Cheers - Bob
  • 0
    If you wish to use sudo for smartctl you will need to either specify the full path (/usr/sbin/smartctl) or add /usr/sbin/ to loginuser's path.
  • 0
    Ok, with su it worked. 

    loginuser@utm9-lan:/home/login > su

    Password:

    utm9-lan:/home/login # smartctl -a /dev/sda

    smartctl 6.0 2012-10-10 r3643 [x86_64-linux-3.8.13.15-119.g03ba714-smp64] (SUSE                                          RPM)

    Copyright (C) 2002-12, Bruce Allen, Christian Franke, www.smartmontools.org

    

    === START OF INFORMATION SECTION ===

    Device Model:     KINGSTON SKC300S37A60G

    Serial Number:    50026B7335005FF7

    LU WWN Device Id: 5 0026b7 335005ff7

    Firmware Version: 507ABBF0

    User Capacity:    60,022,480,896 bytes [60.0 GB]

    Sector Size:      512 bytes logical/physical

    Rotation Rate:    Solid State Device

    Device is:        Not in smartctl database [for details use: -P showall]

    ATA Version is:   ATA8-ACS, ACS-2 T13/2015-D revision 3

    SATA Version is:  SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)

    Local Time is:    Thu Jun 19 21:56:38 2014 WEST

    SMART support is: Available - device has SMART capability.

    SMART support is: Enabled

    

    === START OF READ SMART DATA SECTION ===

    SMART overall-health self-assessment test result: PASSED

    

    General SMART Values:

    Offline data collection status:  (0x00) Offline data collection activity

                                            was never started.

                                            Auto Offline Data Collection: Disabled.

    Self-test execution status:      (   0) The previous self-test routine completed

                                            without error or no self-test has ever

                                            been run.

    Total time to complete Offline

    data collection:                (    0) seconds.

    Offline data collection

    capabilities:                    (0x7b) SMART execute Offline immediate.

                                            Auto Offline data collection on/off supp                                         ort.

                                            Suspend Offline collection upon new

                                            command.

                                            Offline surface scan supported.

                                            Self-test supported.

                                            Conveyance Self-test supported.

                                            Selective Self-test supported.

    SMART capabilities:            (0x0003) Saves SMART data before entering

                                            power-saving mode.

                                            Supports SMART auto save timer.

    Error logging capability:        (0x01) Error logging supported.

                                            General Purpose Logging supported.

    Short self-test routine

    recommended polling time:        (   1) minutes.

    Extended self-test routine

    recommended polling time:        (  48) minutes.

    Conveyance self-test routine

    recommended polling time:        (   2) minutes.

    SCT capabilities:              (0x0021) SCT Status supported.

                                            SCT Data Table supported.

    

    SMART Attributes Data Structure revision number: 10

    Vendor Specific SMART Attributes with Thresholds:

    ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_                                         FAILED RAW_VALUE

      1 Raw_Read_Error_Rate     0x000f   107   107   050    Pre-fail  Always       -                                                16645963

      5 Reallocated_Sector_Ct   0x0033   100   100   003    Pre-fail  Always       -                                                0

      9 Power_On_Hours          0x0032   096   096   000    Old_age   Always       -                                                3728 (103 84 0)

     12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -                                                14

     13 Read_Soft_Error_Rate    0x000a   038   038   000    Old_age   Always       -                                                271656698117963

    100 Unknown_Attribute       0x0032   000   000   000    Old_age   Always       -                                                6177

    170 Unknown_Attribute       0x0032   000   000   000    Old_age   Always       -                                                1664

    171 Unknown_Attribute       0x0032   000   000   000    Old_age   Always       -                                                0

    172 Unknown_Attribute       0x0032   000   000   000    Old_age   Always       -                                                0

    174 Unknown_Attribute       0x0030   000   000   000    Old_age   Offline      -                                                10

    177 Wear_Leveling_Count     0x0000   000   000   000    Old_age   Offline      -                                                5

    181 Program_Fail_Cnt_Total  0x0032   000   000   000    Old_age   Always       -                                                0

    182 Erase_Fail_Count_Total  0x0032   000   000   000    Old_age   Always       -                                                0

    184 End-to-End_Error        0x0032   100   100   090    Old_age   Always       -                                                0

    187 Reported_Uncorrect      0x0032   100   100   000    Old_age   Always       -                                                0

    189 Unknown_SSD_Attribute   0x0000   050   074   000    Old_age   Offline      -                                                68724326450

    194 Temperature_Celsius     0x0022   050   074   000    Old_age   Always       -                                                50 (Min/Max 16/74)

    195 Hardware_ECC_Recovered  0x001c   120   120   000    Old_age   Offline      -                                                16645963

    196 Reallocated_Event_Count 0x0033   100   100   003    Pre-fail  Always       -                                                0

    198 Offline_Uncorrectable   0x0010   107   107   000    Old_age   Offline      -                                                280697587630080

    199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -                                                0

    201 Unknown_SSD_Attribute   0x001c   120   120   000    Old_age   Offline      -                                                16645963

    204 Soft_ECC_Correction     0x001c   120   120   000    Old_age   Offline      -                                                16645963

    230 Unknown_SSD_Attribute   0x0013   100   100   000    Pre-fail  Always       -                                                100

    231 Temperature_Celsius     0x0013   100   100   010    Pre-fail  Always       -                                                0

    232 Available_Reservd_Space 0x0000   000   000   000    Old_age   Offline      -                                                6

    233 Media_Wearout_Indicator 0x0000   000   000   000    Old_age   Offline      -                                                4695

    234 Unknown_Attribute       0x0032   000   000   000    Old_age   Always       -                                                1152

    241 Total_LBAs_Written      0x0032   000   000   000    Old_age   Always       -                                                1152

    242 Total_LBAs_Read         0x0032   000   000   000    Old_age   Always       -                                                12

    

    SMART Error Log not supported

    

    SMART Self-test Log not supported

    

    SMART Selective self-test log data structure revision number 0

    Note: revision number not 1 implies that no selective self-test has ever been ru                                         n

     SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS

        1        0        0  Not_testing

        2        0        0  Not_testing

        3        0        0  Not_testing

        4        0        0  Not_testing

        5        0        0  Not_testing

    Selective self-test flags (0x0):

      After scanning selected spans, do NOT read-scan remainder of disk.

    If Selective self-test is pending on power-up, resume after 0 minute delay.