This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Upgrade help required - missing instructions

Morning all,

I'm attempting an upgrade from 6.312 to 7 and in common with a lot of users here, the web based process fails repeatedly. In order to get around this I have downloaded the sai-7 iso from ftp.astaro.de according to the article at http://www.astaro.org/archive/index.php/t-18519.html but have run into another problem. In that article there is another link to the instructions - http://webreport.astaro.net/content/download/3269/24772/file/V7_SAI+Image_Upgrade_HowTo.txt which is also broken, when I try to browse to it I get:

Object is unavailable

The object you requested is not currently available.

Possible reasons for this are:

    * The id or name of the object was misspelled, try changing it.
    * The object is no longer available on the site.

    * Webmaster
    * Privacy
    * Legal
    * Sitemap

Copyright 2007 by Astaro AG

Can anyone point me at an alternate source please?


This thread was automatically locked due to age.
  • Thanks for the reply alaa, but I guess I'm not "inner circle" enough ;-)


    Access denied

    You don't have permission to access this area.

    Possible reasons for this are:

        * Your current user does not have the proper privileges to access this page.
        * You misspelled some parts of your URL, try changing it.
  • Please download and burn to CD latest Version of sai image available from:

    ftp://sai7:rhasDoal9@ftp.astaro.de/ 

     

    Installation Guide

     

    ASG/SAI ISO

    From Astaro

     

        * 1 About

        * 2 Requirements

        * 3 Estimated time frame

        * 4 Step by step howto

        * 5 Improvements in V7

        * 6 Installing ASG ISO

     

    About

     

    The ASG Autoinstall CD (SAI support appliance installer) runs unattended - it installs an ASG Appliance OEM version.

     

     

    Requirements

     

        * USB CD-ROM drive

        * USB cable

        * Power cable for CD-ROM drive

        * ASG 110/120/220/320/420/425/525

        * Power cable for the ASG 

     

     

    Estimated time frame

    ASG   Time

    110/120     40 min

    220   40 min

    320   20 min

    420   15 min

    425   15 min

    525   15 min

     

     

    Step by step howto

     

        * 1. switch the ASG off

        * 2. plug in the USB-CD-ROM drive (with the Autoinstall-ISO in it) (For ASG 320 it is important to use the USB port at the front)

        * 3. switch the ASG on

        * 4. make sure that "Boot from USB-CDROM" in bios is on first position (default on ASGs)

        * 5. after installation, the ASG starts to beep until it is switched off (for V7 see below) 

               - Success: 1 beep, 1 second sleep, repeated until switched off

               - Failure: 3 short beeps, 2 seconds sleep, repeated until switched off

     

        * 6. remove CD-ROM

        * 7. End 

     

     

    Improvements in V7

     

        * LCD now shows Status infos (for details see LCD_improvements

        * The CD is now autoejected if the installation is finished (needed to see if an ASG_120 is ready since theese do not have LCDs)

        * Old ASG_SERIAL from /etc/asg is taken over (now for V6 and V7)

        * Installation is possible via UDRW USB stick too (simulates a USB CDROM) even on SATA-systems (ASG 425/525) 

     

     

     

    Installing ASG ISO

     

        * The installer runs unattended, all user input is set to default values: 

     

    Keyboard Layout: English(USA)

    Area: Europe/Berlin

    Date/Time: Bios setting

    Admin interface: eth0

     

    Adress: 192.168.0.1

    Netmask: 255.255.255.0

    Gateway: none
  • Thanks very much for your help!