What does the message "No buffer space available" mean and what can i against do?
A part of Deamon-LogFile:
================
2004-Feb 6 03:49:03 firewall named[29719]: master zone "0.0.127.in-addr.arpa" (IN) loaded (serial 1076035741)
2004-Feb 6 03:49:03 firewall named[29719]: listening on [127.0.0.1].53 (lo)
2004-Feb 6 03:49:03 firewall named[29719]: listening on [192.168.1.2].53 (eth0)
2004-Feb 6 03:49:03 firewall named[29719]: Forwarding source address is [0.0.0.0].1060
2004-Feb 6 03:49:03 firewall named[29720]: Ready to answer queries.
2004-Feb 6 03:49:06 firewall pppoe[29323]: send (sendPacket): No buffer space available
2004-Feb 6 03:49:07 firewall pppd[29322]: Modem hangup
2004-Feb 6 03:49:07 firewall pppd[29322]: Connection terminated.
2004-Feb 6 03:49:07 firewall pppd[29322]: Connect time 0.2 minutes.
2004-Feb 6 03:49:07 firewall pppd[29322]: Sent 72805 bytes, received 399 bytes.
2004-Feb 6 03:49:07 firewall pppd[29322]: Exit.
2004-Feb 6 03:49:07 firewall logger: DSL connection time shorter then 60 seconds (13 sec): Error? - wait 900 seconds
2004-Feb 6 03:49:10 firewall named[29720]: ns_forw: sendto([194.25.0.68].53): Network is unreachable
System Interfaces:
============
eth0 Link encap:Ethernet HWaddr 00:40:95:43:4D:96
inet addr:192.168.1.2 Bcast:192.168.1.15 Mask:255.255.255.240
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:124572 errors:0 dropped:0 overruns:0 frame:2648
TX packets:104921 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
Interrupt:10 Base address:0xec00
eth1 Link encap:Ethernet HWaddr 00:00:92:B6:4E:31
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:100650 errors:0 dropped:0 overruns:0 frame:0
TX packets:120223 errors:0 dropped:0 overruns:0 carrier:0
collisions:1051 txqueuelen:100
Interrupt:11 Base address:0xe800
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:2075 errors:0 dropped:0 overruns:0 frame:0
TX packets:2075 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
ppp0 Link encap[:P]oint-to-Point Protocol
inet addr:80.184.157.90 P-t-P:62.104.190.21 Mask:255.255.255.255
UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1492 Metric:1
RX packets:100319 errors:0 dropped:0 overruns:0 frame:0
TX packets:119892 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:3
Do you need more infos?
Thanx
Gustav
PS: Is it ok to increase the MTU for ppp0 from 1454 to 1492 [:S]TU .
This thread was automatically locked due to age.
