Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 8 replies
  • Subscribers 2 subscribers
  • Views 1725 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Can't see access point but webadmin says its up!

Rob_F
Oh.. and I am sooo close...

asl says my wlan0 is up and GREEN. Have setup wlan0 as an access point with WEP enabled.. (had it disabled too).

But I can't see the network?

No matter what I do I cannot connect.

I am using a Compaq WL100 in a Ricoh PCMCIA bridge.
no errors when booting.. I do hear 2 beeps when it starts PCMCIA though..

booting default

I guess I should try noapic although it is seeing the interface just fine... in fact when I change from access point to station I see the kernel log telling me it changed modes.

Hope you can help.. I really don't want to put the Linksys wireless back in service.

Thanks!  


This thread was automatically locked due to age.
Parents
  • 0
    Hi Freyder,
    which version of ASL are you currently using ? - and did you check the HCL if your hardware meets all requirements ?
    best regards,
                      erich  
  • 0 in reply to ehudler
    All patched to the latest  asl v4.019 

    HCL doesn't specify a PCMCIA -> PCI bridge .. or at least I didn't find it there.  WLAN/Prism cards are required.  The WLAN page confirms support for the Compaq WL100 PCMCIA card as a Prism 2 based card.

    I'll try a different laptop and card to eliminate the client side of the equation. 
  • 0 in reply to Rob_F
    Hi !
    It's right above the Prism card's in the HCL !! - for RICOH:

    PCMCIA -> PCI CHIPSETS
    ======================
                                                                     / t / ~ /unS /     N     /
    --RICOH--------------------------------------------|---|---|----|-----------|
    Ricoh RL5C465                                              |    | x |     |              |
    Ricoh RL5C466                                              |    | x |     |              |
    Ricoh RL5C475                                              | x |    |     |              |
    Ricoh RL5C476                                              |    | x |     |              |
    Ricoh RL5C477                                              |    | x |     |              |
    Ricoh RL5C478                                              |    | x |     |              |
    ---------------------------------------------------------------------------|


    regards,
             erich   
Reply
  • 0 in reply to Rob_F
    Hi !
    It's right above the Prism card's in the HCL !! - for RICOH:

    PCMCIA -> PCI CHIPSETS
    ======================
                                                                     / t / ~ /unS /     N     /
    --RICOH--------------------------------------------|---|---|----|-----------|
    Ricoh RL5C465                                              |    | x |     |              |
    Ricoh RL5C466                                              |    | x |     |              |
    Ricoh RL5C475                                              | x |    |     |              |
    Ricoh RL5C476                                              |    | x |     |              |
    Ricoh RL5C477                                              |    | x |     |              |
    Ricoh RL5C478                                              |    | x |     |              |
    ---------------------------------------------------------------------------|


    regards,
             erich   
Children
  • 0 in reply to ehudler
    Ack [:$]choh  ... Sorry about that.

    I have the Ricoh C475 which is tested.

    further analysis shows that the firmware on the WL100 has to be upgraded to support IBSS... working on that now.

    For what its worth... I installed ASL 4 on a laptop with the wl100 in place and got the same errors.   
Cookie Information Banner