Sophos RED 50 - Konfiguration wird nicht von Server geladen

 U-Boot 2010.12 (Jun 13 2012 - 18:57:31)

CPU0: P1020E, Version: 1.1, (0x80ec0011)
Core: E500, Version: 5.1, (0x80212051)
Clock Configuration:
CPU0:533.333 MHz, CPU1:533.333 MHz,
CCB:266.667 MHz,
DDR:333.333 MHz (666.667 MT/s data rate) (Asynchronous), LBC:16.667 MHz
L1: D-cache 32 kB enabled
I-cache 32 kB enabled
Board: P1020RDB Rev
MB-351Z Ver.T03 2012-06-13
I2C: ready
DRAM: Configuring DDR for 666.667 MT/s data rate
DDR: 512 MiB (DDR3, 32-bit, CL=6, ECC off)
FLASH: 2 MiB
L2: 256 KB enabled
NAND: 256 MiB
EEPROM: NXID v0
eTSEC2 is in sgmii mode.

PCIE2: connected to Slot 1 as Root Complex (base addr ffe09000)
PCIE2: Bus 00 - 00

PCIE1: connected to Slot 2 as Root Complex (base addr ffe0a000)
PCIE1: Bus 01 - 01

In: serial
Out: serial
Err: serial
Net: eTSEC1: No support for PHY id ffffffff; assuming generic
eTSEC3: No support for PHY id ffffffff; assuming generic
Init switch to forwarding mode... Done
eTSEC1, eTSEC2, eTSEC3
Hit any key to stop autoboot: 0

NAND read: device 0 offset 0x5100000, size 0x100000
Bad block table found at page 131008, version 0x01
Bad block table found at page 130944, version 0x01
1048576 bytes read: OK

NAND read: device 0 offset 0x5200000, size 0x1000000
16777216 bytes read: OK
## Booting kernel from Legacy Image at 01000000 ...
Image Name: Linux-2.6.38.8
Created: 2012-10-16 14:04:51 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1717541 Bytes = 1.6 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## Flattened Device Tree blob at 00c00000
Booting using the fdt blob at 0xc00000
Uncompressing Kernel Image ... OK
Loading Device Tree to 00ffa000, end 00fffb18 ... OK
[ 0.000000] Using P1020 RDB machine description
[ 0.000000] Memory CAM mapping: 256/256 Mb, residual: 0Mb
[ 0.000000] Linux version 2.6.38.8 (hschaa@sles11) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 SMP Tue Oct 16 16:04:47 CEST 2012
[ 0.000000] CPU maps initialized for 1 thread per core
[ 0.000000] bootconsole [udbg0] enabled
setup_arch: bootmem
mpc85xx_rdb_setup_arch()
[ 0.000000] Found FSL PCI host bridge at 0x00000000ffe09000. Firmware bus number: 0->0
[ 0.000000] PCI host bridge /pcie@ffe09000 ranges:
[ 0.000000] MEM 0x00000000a0000000..0x00000000bfffffff -> 0x00000000a0000000
[ 0.000000] IO 0x00000000ffc30000..0x00000000ffc3ffff -> 0x0000000000000000
[ 0.000000] /pcie@ffe09000: PCICSRBAR @ 0xfff00000
[ 0.000000] Found FSL PCI host bridge at 0x00000000ffe0a000. Firmware bus number: 0->0
[ 0.000000] PCI host bridge /pcie@ffe0a000 ranges:
[ 0.000000] MEM 0x00000000c0000000..0x00000000dfffffff -> 0x00000000c0000000
[ 0.000000] IO 0x00000000ffc20000..0x00000000ffc2ffff -> 0x0000000000000000
[ 0.000000] /pcie@ffe0a000: PCICSRBAR @ 0xfff00000
[ 0.000000] MPC85xx RDB board from Freescale Semiconductor
arch: exit
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00020000
[ 0.000000] Normal empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] MMU: Allocated 1088 bytes of context maps for 255 contexts
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c078f000 s6816 r8192 d13664 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: root=/dev/mtdblock10 console=ttyS0,115200
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] Memory: 515972k/524288k available (3332k kernel code, 8316k reserved, 196k data, 89k bss, 160k init)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffdf000..0xfffff000 : fixmap
[ 0.000000] * 0xfdfda000..0xfe000000 : early ioremap
[ 0.000000] * 0xe1000000..0xfdfda000 : vmalloc & ioremap
[ 0.000000] SLUB: Genslabs=15, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] RCU-based detection of stalled CPUs is disabled.
[ 0.000000] NR_IRQS:512
[ 0.000000] mpic: Setting up MPIC " OpenPIC " version 1.2 at ffe40000, max 2 CPUs
[ 0.000000] mpic: ISU size: 256, shift: 8, mask: ff
[ 0.000000] mpic: Initializing for 256 sources
[ 0.000000] clocksource: timebase mult[7800001] shift[22] registered
[ 0.006348] pid_max: default: 32768 minimum: 301
[ 0.011264] Mount-cache hash table entries: 512
[ 0.018711] mpic: requesting IPIs...
[ 0.127598] Brought up 2 CPUs
[ 0.131852] NET: Registered protocol family 16

[ 0.139555] PCI: Probing PCI hardware
[ 0.143447] pci 0000:00:00.0: ignoring class b20 (doesn't match header type 01)
[ 0.150840] pci 0000:00:00.0: PCI bridge to [bus 01-ff]
[ 0.156750] pci 0001:02:00.0: ignoring class b20 (doesn't match header type 01)
[ 0.164132] pci 0001:02:00.0: PCI bridge to [bus 03-ff]
[ 0.169873] pci 0000:00:00.0: PCI bridge to [bus 01-01]
[ 0.175039] pci 0000:00:00.0: bridge window [io 0xfdfed000-0xfdffcfff]
[ 0.181816] pci 0000:00:00.0: bridge window [mem 0xa0000000-0xbfffffff]
[ 0.188599] pci 0000:00:00.0: bridge window [mem pref disabled]
[ 0.194699] pci 0000:00:00.0: enabling device (0106 -> 0107)
[ 0.200349] pci 0001:02:00.0: PCI bridge to [bus 03-03]
[ 0.205566] pci 0001:02:00.0: bridge window [io 0xfdfdb000-0xfdfeafff]
[ 0.212352] pci 0001:02:00.0: bridge window [mem 0xc0000000-0xdfffffff]
[ 0.219137] pci 0001:02:00.0: bridge window [mem pref disabled]
[ 0.225231] pci 0001:02:00.0: enabling device (0106 -> 0107)
[ 0.235695] bio: create slab <bio-0> at 0
[ 0.240962] usbcore: registered new interface driver usbfs
[ 0.246578] usbcore: registered new interface driver hub
[ 0.252053] usbcore: registered new device driver usb
[ 0.258071] Switching to clocksource timebase
[ 0.265344] NET: Registered protocol family 2
[ 0.269867] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.277041] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.284633] TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.291582] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.298043] TCP reno registered
[ 0.301186] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.307027] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.313794] NET: Registered protocol family 1
[ 0.342574] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.348469] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.359397] msgmni has been set to 1007
[ 0.363434] io scheduler noop registered
[ 0.367302] io scheduler deadline registered (default)
[ 0.573188] Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
[ 0.627281] serial8250.0: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550A
[ 0.634045] console [ttyS0] enabled, bootconsole disabled
[ 0.634045] console [ttyS0] enabled, bootconsole disabled
[ 0.667226] serial8250.0: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550A
[ 0.699587] ffe04500.serial: ttyS0 at MMIO 0xffe04500 (irq = 42) is a 16550
[ 0.735321] ffe04600.serial: ttyS1 at MMIO 0xffe04600 (irq = 42) is a 16550
[ 0.770755] Generic RTC Driver v1.07
[ 0.776433] efe00000.nor: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002249
[ 0.786494] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.791714] Amd/Fujitsu Extended Query version 1.3.
[ 0.796788] number of CFI chips: 1
[ 0.800435] cmdlinepart partition parsing not available
[ 0.805882] RedBoot partition parsing not available
[ 0.810815] Creating 5 MTD partitions on "efe00000.nor":
[ 0.816154] 0x000000000000-0x0000000e0000 : "NOR reserved"
[ 0.823250] 0x0000000e0000-0x0000000f0000 : "NOR env flash2"
[ 0.830470] 0x0000000f0000-0x000000100000 : "NOR env flash"
[ 0.837618] 0x000000100000-0x000000180000 : "NOR Normal mode"
[ 0.844911] 0x000000180000-0x000000200000 : "NOR Backup mode"
[ 0.852769] fsl-lbc ffe05000.localbus: read_byte beyond end of buffer
[ 0.859305] fsl-lbc ffe05000.localbus: read_byte beyond end of buffer
[ 0.865768] fsl-lbc ffe05000.localbus: read_byte beyond end of buffer
[ 0.872234] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron NAND 256MiB 3,3V 8-bit)
[ 0.884289] cmdlinepart partition parsing not available
[ 0.889734] RedBoot partition parsing not available
[ 0.894668] Creating 7 MTD partitions on "ffa00000.flash":
[ 0.900177] 0x000000000000-0x000000100000 : "fdt1"
[ 0.906675] 0x000000100000-0x000001100000 : "uimage1"
[ 0.913341] 0x000001100000-0x000005100000 : "rootfs1"
[ 0.920028] 0x000005100000-0x000005200000 : "fdt2"
[ 0.926430] 0x000005200000-0x000006200000 : "uimage2"
[ 0.933136] 0x000006200000-0x00000a200000 : "rootfs2"
[ 0.939871] 0x00000a200000-0x000010000000 : "data"
[ 0.946354] eLBC NAND device at 0xffa00000, bank 1
[ 0.961177] Fixed MDIO Bus: probed
[ 0.982627] eth0: Gianfar Ethernet Controller Version 1.2, 00:1a:8c:34:4b:a8
[ 0.989710] eth0: Running with NAPI enabled
[ 0.993949] eth0: RX BD ring size for Q[0]: 256
[ 0.998495] eth0: RX BD ring size for Q[1]: 256
[ 1.003040] eth0: RX BD ring size for Q[2]: 256
[ 1.007591] eth0: RX BD ring size for Q[3]: 256
[ 1.012135] eth0: RX BD ring size for Q[4]: 256
[ 1.016679] eth0: RX BD ring size for Q[5]: 256
[ 1.021223] eth0: RX BD ring size for Q[6]: 256
[ 1.025769] eth0: RX BD ring size for Q[7]: 256
[ 1.030314] eth0: TX BD ring size for Q[0]: 256
[ 1.034859] eth0: TX BD ring size for Q[1]: 256
[ 1.039405] eth0: TX BD ring size for Q[2]: 256
[ 1.043949] eth0: TX BD ring size for Q[3]: 256
[ 1.048493] eth0: TX BD ring size for Q[4]: 256
[ 1.053037] eth0: TX BD ring size for Q[5]: 256
[ 1.057583] eth0: TX BD ring size for Q[6]: 256
[ 1.062127] eth0: TX BD ring size for Q[7]: 256
[ 1.078607] eth1: Gianfar Ethernet Controller Version 1.2, 00:1a:8c:34:4b:a9
[ 1.085687] eth1: Running with NAPI enabled
[ 1.089887] eth1: RX BD ring size for Q[0]: 256
[ 1.094434] eth1: RX BD ring size for Q[1]: 256
[ 1.098978] eth1: RX BD ring size for Q[2]: 256
[ 1.103528] eth1: RX BD ring size for Q[3]: 256
[ 1.108073] eth1: RX BD ring size for Q[4]: 256
[ 1.112617] eth1: RX BD ring size for Q[5]: 256
[ 1.117161] eth1: RX BD ring size for Q[6]: 256
[ 1.121708] eth1: RX BD ring size for Q[7]: 256
[ 1.126252] eth1: TX BD ring size for Q[0]: 256
[ 1.130797] eth1: TX BD ring size for Q[1]: 256
[ 1.135344] eth1: TX BD ring size for Q[2]: 256
[ 1.139888] eth1: TX BD ring size for Q[3]: 256
[ 1.144432] eth1: TX BD ring size for Q[4]: 256
[ 1.148977] eth1: TX BD ring size for Q[5]: 256
[ 1.153523] eth1: TX BD ring size for Q[6]: 256
[ 1.158068] eth1: TX BD ring size for Q[7]: 256
[ 1.178609] eth2: Gianfar Ethernet Controller Version 1.2, 00:1a:8c:34:4b:aa
[ 1.185691] eth2: Running with NAPI enabled
[ 1.189891] eth2: RX BD ring size for Q[0]: 256
[ 1.194437] eth2: RX BD ring size for Q[1]: 256
[ 1.198981] eth2: RX BD ring size for Q[2]: 256
[ 1.203530] eth2: RX BD ring size for Q[3]: 256
[ 1.208074] eth2: RX BD ring size for Q[4]: 256
[ 1.212619] eth2: RX BD ring size for Q[5]: 256
[ 1.217163] eth2: RX BD ring size for Q[6]: 256
[ 1.221709] eth2: RX BD ring size for Q[7]: 256
[ 1.226253] eth2: TX BD ring size for Q[0]: 256
[ 1.230798] eth2: TX BD ring size for Q[1]: 256
[ 1.235345] eth2: TX BD ring size for Q[2]: 256
[ 1.239889] eth2: TX BD ring size for Q[3]: 256
[ 1.244433] eth2: TX BD ring size for Q[4]: 256
[ 1.248977] eth2: TX BD ring size for Q[5]: 256
[ 1.253524] eth2: TX BD ring size for Q[6]: 256
[ 1.258068] eth2: TX BD ring size for Q[7]: 256
[ 1.262833] ucc_geth: QE UCC Gigabit Ethernet Controller
[ 1.269129] Freescale PowerQUICC MII Bus: probed
[ 1.274073] mdio_bus mdio@ffe24000: error probing PHY at address 16
[ 1.281411] Freescale PowerQUICC MII Bus: probed
[ 1.287046] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 1.294129] /soc@ffe00000/usb@22000: Invalid 'dr_mode' property, fallback to host mode
[ 1.302422] fsl-ehci fsl-ehci.0: Freescale On-Chip EHCI Host Controller
[ 1.309220] fsl-ehci fsl-ehci.0: new USB bus registered, assigned bus number 1
[ 1.354453] fsl-ehci fsl-ehci.0: irq 28, io mem 0xffe22000
[ 1.370412] fsl-ehci fsl-ehci.0: USB 2.0 started, EHCI 1.00
[ 1.376971] hub 1-0:1.0: USB hub found
[ 1.380771] hub 1-0:1.0: 1 port detected
[ 1.385093] PowerPC Book-E Watchdog Timer Loaded
[ 1.391566] of:talitos ffe30000.crypto: hwrng
[ 1.396094] of:talitos ffe30000.crypto: authenc-hmac-sha1-cbc-aes-talitos
[ 1.403051] of:talitos ffe30000.crypto: authenc-hmac-sha1-cbc-3des-talitos
[ 1.410055] of:talitos ffe30000.crypto: authenc-hmac-sha256-cbc-aes-talitos
[ 1.417156] of:talitos ffe30000.crypto: authenc-hmac-sha256-cbc-3des-talitos
[ 1.424351] of:talitos ffe30000.crypto: authenc-hmac-md5-cbc-aes-talitos
[ 1.431190] of:talitos ffe30000.crypto: authenc-hmac-md5-cbc-3des-talitos
[ 1.438106] of:talitos ffe30000.crypto: cbc-aes-talitos
[ 1.443465] of:talitos ffe30000.crypto: cbc-3des-talitos
[ 1.448903] of:talitos ffe30000.crypto: md5-talitos
[ 1.453916] of:talitos ffe30000.crypto: sha1-talitos
[ 1.459017] of:talitos ffe30000.crypto: sha224-talitos
[ 1.464278] of:talitos ffe30000.crypto: sha256-talitos
[ 1.469549] of:talitos ffe30000.crypto: sha384-talitos
[ 1.474825] of:talitos ffe30000.crypto: sha512-talitos
[ 1.480413] TCP westwood registered
[ 1.483947] NET: Registered protocol family 17
[ 1.488573] Bridge firewalling registered
[ 1.492620] 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
[ 1.499436] All bugs added by David S. Miller <davem@redhat.com>
[ 1.512056] VFS: Mounted root (squashfs filesystem) readonly on device 31:10.
[ 1.519288] Freeing unused kernel memory: 160k init
[ 1.718451] usb 1-1: new high speed USB device using fsl-ehci and address 2
[ 1.857490] hub 1-1:1.0: USB hub found
[ 1.861749] hub 1-1:1.0: 2 ports detected
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
searching for "data"
mounting ramdisk
searching for "NOR reserved"
trying to mount config
binding read-only configuration
checking if partition is valid
trying to mount config
[ 7.443827] JFFS2 notice: (1670) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
merging partitions
overlay of "astaro/cfg"
overlay of "astaro/wifi"
- init -

Please press Enter to activate this console. [ 8.200828] 88E1111
[ 8.618140] Compat-wireless backport release: compat-wireless-2011-08-25
[ 8.624890] Backport based on wireless-testing.git master-2011-09-14
[ 8.748255] cfg80211: Calling CRDA to update world regulatory domain
[ 8.909028] SCSI subsystem initialized
[ 8.981951] cfg80211: World regulatory domain updated:
[ 8.987147] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 8.995529] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.003476] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.011438] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 9.019387] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.027338] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 9.445443] PPP generic driver version 2.4.2
[ 9.606952] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.746293] NET: Registered protocol family 24
[ 9.911183] nf_conntrack version 0.5.0 (8064 buckets, 32256 max)
[ 10.074451] PHY: 0:10 - Link is Up - 1000/Full
[ 10.315488] xt_time: kernel timezone is -0000
[ 10.354449] PHY: 0:02 - Link is Up - 1000/Full
[ 10.510268] Ebtables v2.0 registered
[ 10.750660] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 10.799728] uhci_hcd: USB Universal Host Controller Interface driver
[ 10.895466] usbcore: registered new interface driver ath9k_htc
[ 10.942899] usbcore: registered new interface driver usbserial
[ 10.948861] USB Serial support registered for generic
[ 10.954029] usbcore: registered new interface driver usbserial_generic
[ 10.960618] usbserial: USB Serial Driver core
[ 11.070991] USB Serial support registered for Keyspan - (without firmware)
[ 11.077989] USB Serial support registered for Keyspan 1 port adapter
[ 11.084466] USB Serial support registered for Keyspan 2 port adapter
[ 11.090993] USB Serial support registered for Keyspan 4 port adapter
[ 11.097473] usbcore: registered new interface driver keyspan
[ 11.103184] keyspan: v1.1.5:Keyspan USB to Serial Converter Driver
[ 11.149442] USB Serial support registered for GSM modem (1-port)
[ 11.155706] usbcore: registered new interface driver option
[ 11.161313] option: v0.7.2:USB Driver for GSM modems
[ 11.185534] USB Serial support registered for pl2303
[ 11.190655] usbcore: registered new interface driver pl2303
[ 11.196262] pl2303: Prolific PL2303 USB to serial adaptor driver
[ 11.502198] PHY: mdio@ffe24000:12 - Link is Up - 1000/Full
[ 11.877218] PowerPC Book-E Watchdog Timer Enabled (wdt_period=38)
[ 24.029492] 88E1111
[ 24.643077] device eth0 entered promiscuous mode
[ 24.658158] br-lan: port 1(eth0) entering forwarding state
[ 24.663722] br-lan: port 1(eth0) entering forwarding state
[ 24.779613] 88E1111
[ 24.876216] 88E1111
[ 25.890686] PHY: mdio@ffe24000:12 - Link is Up - 10/Half
[ 25.924325] device redc0 entered promiscuous mode
[ 25.929300] br-lan: port 2(redc0) entering forwarding state
[ 25.934914] br-lan: port 2(redc0) entering forwarding state
[ 25.940529] no peer
[ 26.298476] 88E1111
[ 26.335165] no peer
[ 26.598430] PHY: 0:10 - Link is Up - 1000/Full
[ 26.753434] no peer
[ 27.094434] PHY: 0:02 - Link is Up - 1000/Full
[ 27.306458] PHY: mdio@ffe24000:12 - Link is Up - 10/Half
[ 27.354786] PHY: mdio@ffe24000:12 - Link is Down
[ 27.360509] PHY: mdio@ffe24000:12 - Link is Up - 10/Half
[ 27.406122] no peer
[ 27.810145] no peer
[ 29.406252] no peer
[ 30.155594] no peer
[ 30.266493] no peer
[ 30.970442] br-lan: port 2(redc0) entering forwarding state
[ 30.976083] br-lan: port 1(eth0) entering forwarding state
[ 31.021739] device redc0 left promiscuous mode
[ 31.026255] br-lan: port 2(redc0) entering disabled state
[ 31.031782] device eth0 left promiscuous mode
[ 31.036185] br-lan: port 1(eth0) entering disabled state
[ 33.806139] 88E1111
[ 34.421844] device eth0 entered promiscuous mode
[ 34.437366] br-lan: port 1(eth0) entering forwarding state
[ 34.442910] br-lan: port 1(eth0) entering forwarding state
[ 34.520599] device redc0 entered promiscuous mode
[ 34.525469] br-lan: port 2(redc0) entering forwarding state
[ 34.531079] br-lan: port 2(redc0) entering forwarding state
[ 34.536697] no peer
[ 34.608830] 88E1111
[ 34.703136] 88E1111
[ 34.757398] no peer
[ 35.416461] no peer
[ 35.710707] PHY: mdio@ffe24000:12 - Link is Up - 1000/Half
[ 35.753190] no peer
[ 36.090657] 88E1111
[ 36.378424] PHY: 0:10 - Link is Up - 1000/Full
[ 36.753160] no peer
[ 36.914462] PHY: 0:02 - Link is Up - 1000/Full
[ 37.098609] PHY: mdio@ffe24000:12 - Link is Up - 1000/Half
[ 37.406555] no peer
[ 37.813061] no peer
[ 39.413879] no peer
[ 39.491292] PHY: mdio@ffe24000:12 - Link is Up - 1000/Full
[ 39.524708] PHY: mdio@ffe24000:12 - Link is Down
[ 39.530560] PHY: mdio@ffe24000:12 - Link is Up - 1000/Full
[ 40.162431] no peer
[ 41.153014] no peer
[ 41.412238] no peer
[ 42.153013] no peer
[ 43.039859] no peer
[ 43.412867] no peer
[ 44.725997] no peer
[ 45.214676] no peer
[ 45.413048] no peer
[ 45.584271] no peer
[ 46.274653] red_tx_skb: 1 callbacks suppressed
[ 46.279124] no peer
[ 46.722963] no peer
[ 47.407614] no peer
[ 47.815964] no peer
[ 48.163285] no peer
[ 48.714512] no peer
[ 49.162850] no peer
[ 49.407219] no peer
[ 50.162873] no peer
[ 50.262441] br-lan: port 2(redc0) entering forwarding state
[ 50.268084] br-lan: port 1(eth0) entering forwarding state
[ 50.293529] device redc0 left promiscuous mode
[ 50.298042] br-lan: port 2(redc0) entering disabled state
[ 50.303542] device eth0 left promiscuous mode
[ 50.307946] br-lan: port 1(eth0) entering disabled state
[ 54.808219] Restarting system.

Ich hoffe mir kann jemand den entscheidenden Tip geben. 

VG

Franki