This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

5.020 License counting.

What is happening with this???  Some documentation and/or warning from Astaro would have been good to tell us what exactly this up2date will do for licensing  [:O]

Will excess licenses currently get blocked from accessing the net yet or is that still to come?  This should all be FULLY documented before it is implemented.

As far as I was aware there was still issues with the license counting/refresh intervals that needed resolving.

Earlier this evening I did a license count reset BEFORE installing 5.020

I have a 50IP license.

ASL Webmin reports 6 IP addresses currently in use.

ASL just emailed me:

"This email was sent by your Astaro Security Linux software to notify you that you have exceeded 100% of the user count for your license!

Additional users may not be able to reach the Internet through the Astaro Security Linux firewall. Astaro is not responsible for providing secure access for additional users.

You will be able to exceed the licensed user count by a small margin, but please act immediately to assure continuous, secure internet access for your users. Please contact your Astaro solutions partner or Astaro to discuss upgrading your license.

Thank you,

Astaro
http://www.astaro.com


--
Last WebAdmin login: admin at Fri Aug 27 19:21:18 from 192.168.3.30
System Uptime      : 0 days 1 hours 3 minutes
System Load        : 0.17
System Version     : Astaro Security Linux 5.020
License usage      : 13 of 50 users active"

Now webmin and the email notification do not agree...
"Current users (IPs) listing    Total 6 entries "

Not very impressed, especially since there are quite a few other issues open that would appear to me to be more important than license checking.


This thread was automatically locked due to age.
Parents
  • same notification here License usage: EXCEEDING 100% OF USER COUNT on Astaro Security Linux..
  • Maybe it's an initial implementation thing...

    Still all my comments above stand.

    Also, Executive Report says I'm using 15IP's whilst Admin-Licensing says I'm using 13 now....
  • I guess the differences between the user numbers are due to these facts ..

    1) notification email listing somehow cumulative user number:
    License usage : 13 of 50 users active

    2) Webadmin showing current users:
    "Current users (IPs) listing Total 6 entries"

    3) Executive Report showing an average over certain time.

    I am not saying this is very consistent, just trying to find a reason for different numbers. Haven't tested it on my system, so don't have own experience.
  • Hi there all guys, 

    let me try to explain this, 
    before this rumor spreads.

    In General
    ---------------
    Astaro Security Linux V5 is licensed based on Users.
    A User is an IP Address that communicates through the firewall either with the internet or through a vpn tunnel.
    i.e: If you have a 50 user license, you purchased the right to have 50 IPs in your network that communicate through the firewall with the internet or though a vpn tunnel. 

    If you have computers inside your network that do not communicate with the internet or through a vpn tunnel, they do not need to be licensed, even if they are protected by our product, this is a new benefit of the ASL V5 licensing model.

    In order to allow communication through the firewall,  you need to create a packet filter rule that allows this.
    Therefore you can fully control which Users/IPs are allowed to connect the internet and get counted and which not.

    The licensing model of ASL V5 has never been changed.

    We have integrated a licensing daemon in ASL V5 that counts those Users and notify the administrator if there is the risk that his installation is going to exceed the purchased license. In that case we send a notification to inform the administrator.
    The administrator can verify the actual User Count in WebAdmin > Licensing > Licensed Users - click Start.

    He can verify the ip addresses of the counted Users there, as well as when they have been first and last seen.
    Additionally you will find a graph in the reporting section that also shows you your actual and historical user count.

    If something happend or if you are changing your network setup, you can reset the counted user list by clicking on 'Start ' in the 'Reset user (IPs) listing:'.
    This is followed by a reboot.

    Up2Date 5.020
    ----------------------
    In this up2date we addressed mainly two things:
    1) we improved the accuracy of the licensing daemon to no longer generate false positives, Simon Shaw was very helpfull to track them down, thx for that.
    2) fixed a bug in the monitoring sytem that prevented the sending of notification emails in certain cases, this included the licensing notification.
    this issues have now been fixed.

    I hope this awnsers the open licensing questions.

    regards
    Gert
  • [ QUOTE ]
    I guess the differences between the user numbers are due to these facts ..

    1) notification email listing somehow cumulative user number:
    License usage : 13 of 50 users active

    2) Webadmin showing current users:
    "Current users (IPs) listing Total 6 entries"

    3) Executive Report showing an average over certain time.

    I am not saying this is very consistent, just trying to find a reason for different numbers. Haven't tested it on my system, so don't have own experience. 

    [/ QUOTE ]

    1) and 2) should be identical (if based on the same point of time - of course).

    If you have root access to the ASL, see lines "successfully linearized n users" in /var/log/license.log for 5-minutes-accuracy.
    Else the listing in Webadmin shows the most current number.

    Your comment on 3) seems plausible.
  • I have checked this on my home firewall, 
    and all three occurences show the same number.

    regards
    Gert
  • Well, it doesn't "cut me off" if I'm using too many licenses. Great. But what is it good for then? I have a ten IP license here and 2 systems using it. I had a disk-crash last night, so started from scratch this morning. Right now there is one system running. Webadmin tells me there is one IP using the box. So okay, but still I get a mail from the box telling me I'm exceeding the license? This (sorry for the bad language) SUX!

    What I did now is set a filter in thunderbird, to send these mails to /dev/null. 

    I think it doesn't make any sense at all, bugging people with some functionality, that, if it was working, would useful, but at the moment is just using time, space (as in hard disk space) and capacity (as in processor time and bandwidth).

    Why?

    hey.. and why isn't there an angry smiley in the list??? *g*
  • Gert, thanks for the acknowledge and clarifications.  I think you should have posted that message first before putting up the up2date but *shrug*. [:)]

    I guess my main concern is the cumulative IP counting that the license counter uses and how long a period an IP will be counted before it's no longer considered "protected" under the license.

    IMHO an IP should stop being counted against the license limit the moment it's switched off, removed, disconnects or whatever.  I know this would be difficult to implement but just what is the time limit going to be?

    We have a number of transient IP's used and this issue concerns me.  (ie Staff / Clients visiting often with laptops, training room PC's, PDA's coming and going etc.)
Reply
  • Gert, thanks for the acknowledge and clarifications.  I think you should have posted that message first before putting up the up2date but *shrug*. [:)]

    I guess my main concern is the cumulative IP counting that the license counter uses and how long a period an IP will be counted before it's no longer considered "protected" under the license.

    IMHO an IP should stop being counted against the license limit the moment it's switched off, removed, disconnects or whatever.  I know this would be difficult to implement but just what is the time limit going to be?

    We have a number of transient IP's used and this issue concerns me.  (ie Staff / Clients visiting often with laptops, training room PC's, PDA's coming and going etc.)
Children
No Data