Hi All
I was just looking through the Kernal log for a differnet Fault and came across references to redw0 as I have no "Red" devices attached.
I assume that this is the internal refenrence for my AP10 that I have attached to my UTM.
(I assume that the Kernal logs events may have been triggered by turning on IPv6. I have been turning on and on services over the last couple of days).
2013:02:18-13:14:23 fmaster kernel: [501900.985196] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready
2013:02:18-13:14:23 fmaster kernel: [501900.987012] IPv6: ADDRCONF(NETDEV_UP): eth5: link is not ready
2013:02:18-13:14:23 fmaster kernel: [501900.987039] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
2013:02:18-13:14:23 fmaster kernel: [501900.987041] IPv6: ADDRCONF(NETDEV_UP): wlan2: link is not ready
2013:02:18-13:14:23 fmaster kernel: [501900.987100] IPv6: ADDRCONF(NETDEV_UP): sit0: link is not ready
2013:02:18-13:14:23 fmaster kernel: [501901.089798] RED: redw0: no route
2013:02:18-13:14:23 fmaster kernel: [501901.097798] RED: redw0: no route
2013:02:18-13:14:23 fmaster kernel: [501901.117772] RED: redw0: no route
2013:02:18-13:14:23 fmaster kernel: [501901.297583] wlan1: port 1(redw0.101) entered disabled state
2013:02:18-13:14:23 fmaster kernel: [501901.318737] e1000: eth0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
2013:02:18-13:14:23 fmaster kernel: [501901.319940] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
2013:02:18-13:14:23 fmaster kernel: [501901.319943] 8021q: adding VLAN 0 to HW filter on device eth0
2013:02:18-13:14:23 fmaster kernel: [501901.320230] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
2013:02:18-13:14:24 fmaster kernel: [501901.402223] e1000: eth4 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
2013:02:18-13:14:24 fmaster kernel: [501901.409306] 8021q: adding VLAN 0 to HW filter on device eth4
2013:02:18-13:14:24 fmaster kernel: [501901.450272] e1000: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: None
2013:02:18-13:14:24 fmaster kernel: [501901.451134] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
2013:02:18-13:14:24 fmaster kernel: [501901.451137] 8021q: adding VLAN 0 to HW filter on device eth2
2013:02:18-13:14:24 fmaster kernel: [501901.451699] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
2013:02:18-13:14:24 fmaster kernel: [501901.481156] wlan1: port 1(redw0.101) entered forwarding state
2013:02:18-13:14:24 fmaster kernel: [501901.481198] wlan1: port 1(redw0.101) entered forwarding state
2013:02:18-13:14:39 fmaster kernel: [501916.498130] wlan1: port 1(redw0.101) entered forwarding state
Mark
