Thread Info
  • State Not Answered
  • Locked Locked
  • Replies 18 replies
  • Subscribers 31 subscribers
  • Views 26561 views
  • Users 0 members are here
Options
Suggested
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Strange problem with 17.0.3 MR3 on intel j1900

Vladislav Bidikov

Hi all,

 

Finally got some free time to install SFOS for my home network so i was thinking that a 4 port j1900 with 32SSD will be more than sufficient (several home pc and mobile devices)

Install went smooth...

Connected LAN2 (WAN) to network (another router with DHCP, so double NAT is here)

Connected PC to LAN 1 (LAN) - ip is default 172.16.16.16

 

After 30 seconds i get internet access (which means that traffic is going with the default settings) on the PC but i cannot access https://172.16.16.16:4444

If i use the console to debug the interfaces i see that IP on the interfaces are fine...

Amy idea what is the problem and maybe where can i find the MR2 iso in order to try to install...

Before trying to install sfos - the same micro PC was running pfsense for a quick test and all of the hardware was fine ...

 

Please advice any ideas....



This thread was automatically locked due to age.
Parents Reply Children
  • 0 in reply to Aditya Patel

    Well the mini pc came with 32GB SSD :(

    Never had the idea that maybe that could be the problem... since it's a hardware device - attaching a new hdd could be an interesting process...

     

    Can you verify that 80GB Disk is the minimal ???

  • 0 in reply to Vladislav Bidikov

    Hi Vladislav ,

    It is a recommended requirement, the minimum is 20GB but that could have changed so need to verify it.  Are you able to access Console of the XG after setup ?

  • 0 in reply to Aditya Patel

    On the VGA i see the standard console (with attached usb keyboard)...

    That is the second way i was able to verify that both interfaces are up (lan has default ip 172.16.16.16, wan has DHCP), DNS is ok and internet connectivity seems ok...

    The first way was that if i connect to LAN i get dhcp ip (from range 172.16.16.16) and if i config ip manually also i get ping reply...

     

    I'm looking into the possibility to use a bigger hdd temporally to verify this new moment with a 32GB hdd that is maybe too small ...

     

     

     

     

  • 0 in reply to Aditya Patel

    Just to update...

    i'm still waiting for a bigger msata SSD to arrive...

     

    In the mean time, i tried the recommendation to activate device management from the console with out any effect...

    Also, i went into advanced shell and did a "netstat -nlp" and did not see any process listening on port 4444, while i see almost all other ports fine (23,22, 25, 8009, etc ...)

     

    Anything else i can try while i wait for a bigger HDD ???

     

  • 0 in reply to Vladislav Bidikov

    I had a similar issue when I first setup XG on my J1900.

     

    There was only 1 ip address that the admin would initially respond to one IP address, IIRC I needed to set it to 172.16.16.1 for it to work for me.

     

    Once I had done initial setup and moved the main LAN network to the IP addresses I used, I can access from any LAN ip.

  • 0 in reply to Ian Rogers

    Well what still bugs me i why there i no process listening on port 4444 TCP ...

    Even if it's something to do with a firewall ACL port on the XG itself must be in listening state...

     

    Tried a VM install with 40GB HDD - works like expected...