Hi List,
As soon as a ASC tried with the ASL to connect i get myself the following error message.
ipsec.log
2005:07:18-11:26:08 (none) pluto[23248]: packet from 192.168.1.68:500: ignoring unknown Vendor ID payload [da8e937880010000]
2005:07:18-11:26:08 (none) pluto[23248]: packet from 192.168.1.68:500: received Vendor ID payload [XAUTH]
2005:07:18-11:26:08 (none) pluto[23248]: packet from 192.168.1.68:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-03] method set to=108
2005:07:18-11:26:08 (none) pluto[23248]: packet from 192.168.1.68:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-02_n] meth=106, but already using method 108
2005:07:18-11:26:08 (none) pluto[23248]: packet from 192.168.1.68:500: received Vendor ID payload [draft-ietf-ipsec-nat-t-ike-00]
2005:07:18-11:26:08 (none) pluto[23248]: packet from 192.168.1.68:500: received Vendor ID payload [RFC 3947] method set to=109
2005:07:18-11:26:08 (none) pluto[23248]: packet from 192.168.1.68:500: received Vendor ID payload [Dead Peer Detection]
2005:07:18-11:26:08 (none) pluto[23248]: packet from 192.168.1.68:500: ignoring unknown Vendor ID payload [101fb0b35c5a4f4c08b919f1ce0d3e4a]
2005:07:18-11:26:08 (none) pluto[23248]: packet from 192.168.1.68:500: received Vendor ID payload [Cisco-Unity]
2005:07:18-11:26:08 (none) pluto[23248]: "S_NCP-TEST_0"[9] 192.168.1.68 #45: responding to Main Mode from unknown peer 192.168.1.68
2005:07:18-11:26:08 (none) pluto[23248]: "S_NCP-TEST_0"[9] 192.168.1.68 #45: policy does not allow OAKLEY_RSA_SIG authentication. Attribute OAKLEY_AUTHENTICATION_METHOD
2005:07:18-11:26:08 (none) pluto[23248]: "S_NCP-TEST_0"[9] 192.168.1.68 #45: no acceptable Oakley Transform
2005:07:18-11:26:08 (none) pluto[23248]: "S_NCP-TEST_0"[9] 192.168.1.68 #45: sending notification NO_PROPOSAL_CHOSEN to 192.168.1.68:500
2005:07:18-11:26:08 (none) pluto[23248]: "S_NCP-TEST_0"[9] 192.168.1.68 #45: failed to build notification for spisize=0
2005:07:18-11:26:08 (none) pluto[23248]: "S_NCP-TEST_0"[9] 192.168.1.68: deleting connection "S_NCP-TEST_0" instance with peer 192.168.1.68 {isakmp=#0/ipsec=#0}
With the version ASL5 there were no problems.
Basis for the ASL6 installation was the backup file of the ASL5.
An import on the ASC from the ASL6 generated User Config file, are not successful also.
What is the problem?
Stefan
This thread was automatically locked due to age.
