This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Upgrading ASG 220

Can someone point me to right docs?
[:(]

- I am trying to upgrade to v7 from v6. - There is no monitor port on the 220 and the console port(s) do not seem to be active.

- I have upgraded a 110 succesfully with the USB ISO booting process.

- I can not find any other instrustions on how to get the install to update or can I find and install wizard docs to update the license and confiruration prior to the install.

- I can not find the docs on how to use the up2date feature to update the router.

---- Please help by providing links or article numbers to documetation on how to update the ASG 220.

THIS DOES NOT WORK FOR ASG 220 [:S]
Step by step howto

    * 1. switch the ASG off
    * 2. plug in the USB-CD-ROM drive (with the Autoinstall-ISO in it) (For ASG 320 it is important to use the USB port at the front)
    * 3. switch the ASG on
    * 4. make sure that "Boot from USB-CDROM" in bios is on first position (default on ASGs)
    * 5. after installation, the ASG starts to beep until it is switched off (for V7 see below)
           - Success: 1 beep, 1 second sleep, repeated until switched off
           - Failure: 3 short beeps, 2 seconds sleep, repeated until switched off

    * 6. remove CD-ROM
    * 7. End

Thanks for your help....

This thread was automatically locked due to age.

0 KKnecht over 18 years ago

Which installation cd are you using ?
There is a special one for ASGs, which is normally only available for partners.
They will help you to upgrade your system.
Your configuration can't be migrated right now. Migration is told to be available March/April
Cancel
Vote Up 0 Vote Down

Cancel
0 technutz over 18 years ago in reply to KKnecht

Karsten:

I am using asg-7.002-070302-1.iso. I have successfully upgrade seven 110's without issue. I just cannot do the 220. Is this the correct ISO?

Thanks!
Technutz
Cancel
Vote Up 0 Vote Down

Cancel
0 BrucekConvergent over 18 years ago in reply to technutz

wrong iso, the right one starts with sai in the file name. Contact your reseller, they should be able to help you out.

CTO, Convergent Information Security Solutions, LLC

https://www.convergesecurity.com

Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries. Use the advice given at your own risk.
Cancel
Vote Up 0 Vote Down

Cancel
0 technutz over 18 years ago in reply to BrucekConvergent

Thanks! I have done so now and I have the new ISO. Thanks again!
Cancel
Vote Up 0 Vote Down

Cancel
0 3r8 over 18 years ago in reply to technutz

Did that work for you? I have the "SAI" iso and I followed the instructions but nothing is happening.
Cancel
Vote Up 0 Vote Down

Cancel
0 BrucekConvergent over 18 years ago in reply to 3r8

The sai image worked fine on a 320 I upgraded to 7.002 the other day.

CTO, Convergent Information Security Solutions, LLC

https://www.convergesecurity.com

Advice given as posted on this forum does not construe a support relationship or other relationship with Convergent Information Security Solutions, LLC or its subsidiaries. Use the advice given at your own risk.
Cancel
Vote Up 0 Vote Down

Cancel
0 lantech over 18 years ago in reply to BrucekConvergent

[v7.002]
I upgraded our 220 the same week the ISO came out. worked great. Could it be your system is not detecting the usb cdrom? I used a samsung dvd rw drive. It took a good 45min to complete if I remember correctly, but it went just as expected.
Cancel
Vote Up 0 Vote Down

Cancel
0 Pie over 18 years ago in reply to lantech

Hi there,

how do i get the Image to an USB Stick?
My former Reseller provided me with a Stick for the v5 ages ago, but I don't have it anymore to compare...

Have not an ASG but a SecuTrends Appliance.

Help would be much appreciated.

- Pie
Cancel
Vote Up 0 Vote Down

Cancel
0 RufusToofus over 18 years ago in reply to Pie

The appliance needs the "reseller "SAI" version" The Open ISO will work, but your licence won't work as it will see the applaince as a 3rd party hardwar unit instead. I upgraded an ASG Fine then my older one ASG220 wouldn't go .. used the "special" VGA cable that fits the MOtheRBOARD, found that the BIOS was NOT set to boot from USB CDROM.
As for USB stick, if it won't go on a CDROM then nor will USB stick. IT's at the hardware level you need to look .....
Cancel
Vote Up 0 Vote Down

Cancel
0 r.wijninga over 18 years ago in reply to RufusToofus

Where can I find some more info on this 'special' vga cable? My ASG220 hangs with the message ASG Installation Pre-install - E. That's why I would like to see where it hangs.
Cancel
Vote Up 0 Vote Down

Cancel