This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Intel Pro 1000MT Dual NIC ?

Hi,
I have a Dell PowerEdge 1850 server on wich I am trying to install ASL v6.100 on. The server has 2x Intel Pro 1000MT dual Nics in PCI-e slots, and 2 onboard nics.

During installation only 2 onboard nics is detected by Astaro. The Pro 1000MT dual nics are not detected.
I have checked the HCL and the Pro 1000MT cards are here !

What is going on ? Do I need to do something special to make this work ?
Its very frustrating to buy hardware on the HCL - and discover that it does'nt work with Astaro.

Please advice.

Best Regards
Jonas

This thread was automatically locked due to age.

0 KKnecht over 20 years ago

Using DELL PowerEdge server as ASL with 2 onboard NICs and 2 Intel PCI DualPort NICs, so 6 ports in summary.
Working fine since V5, also V6.1.
Not in the office, so don't know hardware details, but remember something that BIOS settings had to be checked well.
Cancel
Vote Up 0 Vote Down

Cancel
0 Simon Shaw over 20 years ago in reply to KKnecht

Theres a few different flavours of 1000MT cards it seems.

I think they changed chip somewhere along the line...
Cancel
Vote Up 0 Vote Down

Cancel
0 DrJones over 20 years ago in reply to Simon Shaw

KKnecht - do you have more info on these BIOS settings ?

Best Regards,
Jonas
Cancel
Vote Up 0 Vote Down

Cancel
0 DrJones over 20 years ago in reply to DrJones

If I run a LSPCI - I get this ;

Onboard NICs ;
0000:08:07.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller (rev 05)
0000:09:08.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit Ethernet Controller (rev 05)

Pro 1000MT Nics ;
0000:0b:04.0 Ethernet controller: Intel Corp.: Unknown device 108a (rev 03)
0000:0b:04.1 Ethernet controller: Intel Corp.: Unknown device 108a (rev 03)

Best Regards,
Jonas
Cancel
Vote Up 0 Vote Down

Cancel
0 ALT over 20 years ago in reply to Simon Shaw

I want buy some nics with dual port or quad port, but I want know if Intel's nic will work. Whant brand of nic's do you recommend buy ????
Cancel
Vote Up 0 Vote Down

Cancel
0 ronzle over 20 years ago

Hi DrJones

We list only cards at the HCL, which we tested in our lab.
Now it could be that Intel changed the PCI-ID or other things for newer cards . [:S]
So can you do following:

lspci -vvx > file2.txt
lspci -vvxn > file1.txt

Please send me this files to hardware@astaro.com.

regards
ronny
Cancel
Vote Up 0 Vote Down

Cancel
0 DrJones over 20 years ago in reply to ronzle

Hi Ronny,

Files has been sent.

- Looking forward to your reply.

Best Regards,
Dr.Jones
Cancel
Vote Up 0 Vote Down

Cancel
0 seezer over 20 years ago in reply to ALT

ALT: got an intel quad 1000MT - works fine using e1000 driver. (tested since the V6betas)
Cancel
Vote Up 0 Vote Down

Cancel
0 DrJones over 20 years ago in reply to seezer

Hi Seezer,

Is your Intel card based on PCI-e ?

Regards,
Jonas
Cancel
Vote Up 0 Vote Down

Cancel
0 FatAndy over 20 years ago in reply to DrJones

Hi DrJones,
Intel has only PCI-X version of quad-port 1000 MT Server adapter based on two 82546 chips, please see here:
http://support.intel.com/support/network/sb/cs-012904.htm
And PCIe is available with 8257x chips only:
http://developer.intel.com/design/network/products/ethernet/linecard_ec.htm
Unfortunately I can't see any separate boards produced by Intel itself based on 8257x chips, only LOMs...

I have the same problem BTW with 82573 LOM chips on PCI Express bus and ASG 6.102
Cancel
Vote Up 0 Vote Down

Cancel